Today, after about 15 years of using VBar, my Logo 200 with V8.2 finally failed.
No problems before the update to V8.2 (approx. 70 flights).
Always flown from the same airfield.
Flight No. 86 went smoothly again.
Unfortunately, one of the landing gear struts broke.
The transmitter is a first-generation VBar Touch with the latest software.
Are there any similar experiences with V8.2 here?
*******************
07/27/2026 4:38:39 p.m.;VBar Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:38:39 Good; Cold start
27.07.2026 16:38:40 Good; Reset Reason: Power On
27.07.2026 16:38:41 Good; OMP controller detected
27.07.2026 16:38:41 Good; Bank 1 loaded
27.07.2026 16:38:43 Good; Calibration complete
27.07.2026 16:38:45 Good; Top 5 battery choice: GensAce 750
27.07.2026 16:39:03 Info; Speed controller switched ON
27.07.2026 16:39:04 Good; Engine switch Idle Start
27.07.2026 16:39:04 Good; Motor switch Motor On
27.07.2026 16:39:13 Good; Bank 2 loaded
07/27/2026 4:41:35 PM;VBar Logfile End -- 07/27/2026 -- 4:41:34 PM
27.07.2026 16:41:35 Good; OMP controller disconnected
07/27/2026 4:41:38 p.m.;VBar Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:41:38 Warning; RC input package lost
27.07.2026 16:41:39 Error; RC Failsafe activated
27.07.2026 16:41:39 Good; OMP controller detected
27.07.2026 16:41:40 Warning; Rev controller at full throttle
27.07.2026 16:41:40 Info; Rev controller is at the lower throttle limit
27.07.2026 16:41:41 Warning; Rev controller at full throttle
27.07.2026 16:41:45 Info; Speed controller switched to OFF
07/27/2026 4:41:45 p.m. Info;Off - Controller - Umin:11.0V Imax:8.4A Temp:34?
27.07.2026 16:41:45 Good; Motor switch Motor Off
27.07.2026 16:41:46 Info; Speed controller switched ON
27.07.2026 16:41:46 Warning; Rev controller at full throttle
07/27/2026 4:41:46 p.m. Info;Off - Controller - Umin:11.3V Imax:0.0A Temp:33?
27.07.2026 16:41:46 Good; Motor switch Motor On
27.07.2026 16:41:47 Warning; rev controller at full throttle
27.07.2026 16:41:47 Info; Speed controller switched to OFF
27.07.2026 16:41:47 Warning; rev controller at full throttle
27.07.2026 16:41:47 Good; Motor switch Motor Off
27.07.2026 16:41:48 Good; Bank 1 loaded
07/27/2026 4:44:43 p.m.;VBar Logfile End -- 07/27/2026 -- 4:44:43 p.m
27.07.2026 16:44:44 Good; OMP controller disconnected
No problems before the update to V8.2 (approx. 70 flights).
Always flown from the same airfield.
Flight No. 86 went smoothly again.
Unfortunately, one of the landing gear struts broke.
The transmitter is a first-generation VBar Touch with the latest software.
Are there any similar experiences with V8.2 here?
*******************
07/27/2026 4:38:39 p.m.;VBar Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:38:39 Good; Cold start
27.07.2026 16:38:40 Good; Reset Reason: Power On
27.07.2026 16:38:41 Good; OMP controller detected
27.07.2026 16:38:41 Good; Bank 1 loaded
27.07.2026 16:38:43 Good; Calibration complete
27.07.2026 16:38:45 Good; Top 5 battery choice: GensAce 750
27.07.2026 16:39:03 Info; Speed controller switched ON
27.07.2026 16:39:04 Good; Engine switch Idle Start
27.07.2026 16:39:04 Good; Motor switch Motor On
27.07.2026 16:39:13 Good; Bank 2 loaded
07/27/2026 4:41:35 PM;VBar Logfile End -- 07/27/2026 -- 4:41:34 PM
27.07.2026 16:41:35 Good; OMP controller disconnected
07/27/2026 4:41:38 p.m.;VBar Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:41:38 Warning; RC input package lost
27.07.2026 16:41:39 Error; RC Failsafe activated
27.07.2026 16:41:39 Good; OMP controller detected
27.07.2026 16:41:40 Warning; Rev controller at full throttle
27.07.2026 16:41:40 Info; Rev controller is at the lower throttle limit
27.07.2026 16:41:41 Warning; Rev controller at full throttle
27.07.2026 16:41:45 Info; Speed controller switched to OFF
07/27/2026 4:41:45 p.m. Info;Off - Controller - Umin:11.0V Imax:8.4A Temp:34?
27.07.2026 16:41:45 Good; Motor switch Motor Off
27.07.2026 16:41:46 Info; Speed controller switched ON
27.07.2026 16:41:46 Warning; Rev controller at full throttle
07/27/2026 4:41:46 p.m. Info;Off - Controller - Umin:11.3V Imax:0.0A Temp:33?
27.07.2026 16:41:46 Good; Motor switch Motor On
27.07.2026 16:41:47 Warning; rev controller at full throttle
27.07.2026 16:41:47 Info; Speed controller switched to OFF
27.07.2026 16:41:47 Warning; rev controller at full throttle
27.07.2026 16:41:47 Good; Motor switch Motor Off
27.07.2026 16:41:48 Good; Bank 1 loaded
07/27/2026 4:44:43 p.m.;VBar Logfile End -- 07/27/2026 -- 4:44:43 p.m
27.07.2026 16:44:44 Good; OMP controller disconnected
Heute hat es mich nach ca. 15 Jahren VStabi mit meinem Logo 200 mit V8.2 erwischt.
Vor dem Update auf V8.2 (ca. 70 Flüge) keine Probleme.
Geflogen immer auf der selben Flugstelle.
Flug Nr. 86 wieder ohne Probleme.
Leider ein Bügel von Landegestell gebrochen.
Sender ist VBar Touch erste Generation mit neuester Software.
Gibt es hier ähnliche Erfahrungen mit V8.2?
*******************
27.07.2026 16:38:39;VStabi Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:38:39 Gut;Kaltstart
27.07.2026 16:38:40 Gut;Reset Grund: Power On
27.07.2026 16:38:41 Gut;OMP Regler erkannt
27.07.2026 16:38:41 Gut;Bank 1 geladen
27.07.2026 16:38:43 Gut;Kalibrierung beendet
27.07.2026 16:38:45 Gut;Top 5 Akkuwahl: GensAce 750
27.07.2026 16:39:03 Info;Drehzahlregler auf AN geschaltet
27.07.2026 16:39:04 Gut;Motorschalter Leerlauf Durchstarten
27.07.2026 16:39:04 Gut;Motorschalter Motor An
27.07.2026 16:39:13 Gut;Bank 2 geladen
27.07.2026 16:41:35;VBar Logfile End -- 27.07.2026 -- 16:41:34
27.07.2026 16:41:35 Gut;OMP Regler getrennt
27.07.2026 16:41:38;VStabi Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:41:38 Warn;RC Eingangspaket verloren
27.07.2026 16:41:39 Fehler;RC Failsafe aktiviert
27.07.2026 16:41:39 Gut;OMP Regler erkannt
27.07.2026 16:41:40 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:40 Info;Drehzahlregler ist am unteren Gaslimit
27.07.2026 16:41:41 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:45 Info;Drehzahlregler auf AUS geschaltet
27.07.2026 16:41:45 Info;Aus - Regler - Umin:11.0V Imax:8.4A Temp:34?
27.07.2026 16:41:45 Gut;Motorschalter Motor Aus
27.07.2026 16:41:46 Info;Drehzahlregler auf AN geschaltet
27.07.2026 16:41:46 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:46 Info;Aus - Regler - Umin:11.3V Imax:0.0A Temp:33?
27.07.2026 16:41:46 Gut;Motorschalter Motor An
27.07.2026 16:41:47 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:47 Info;Drehzahlregler auf AUS geschaltet
27.07.2026 16:41:47 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:47 Gut;Motorschalter Motor Aus
27.07.2026 16:41:48 Gut;Bank 1 geladen
27.07.2026 16:44:43;VBar Logfile End -- 27.07.2026 -- 16:44:43
27.07.2026 16:44:44 Gut;OMP Regler getrennt
Vor dem Update auf V8.2 (ca. 70 Flüge) keine Probleme.
Geflogen immer auf der selben Flugstelle.
Flug Nr. 86 wieder ohne Probleme.
Leider ein Bügel von Landegestell gebrochen.
Sender ist VBar Touch erste Generation mit neuester Software.
Gibt es hier ähnliche Erfahrungen mit V8.2?
*******************
27.07.2026 16:38:39;VStabi Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:38:39 Gut;Kaltstart
27.07.2026 16:38:40 Gut;Reset Grund: Power On
27.07.2026 16:38:41 Gut;OMP Regler erkannt
27.07.2026 16:38:41 Gut;Bank 1 geladen
27.07.2026 16:38:43 Gut;Kalibrierung beendet
27.07.2026 16:38:45 Gut;Top 5 Akkuwahl: GensAce 750
27.07.2026 16:39:03 Info;Drehzahlregler auf AN geschaltet
27.07.2026 16:39:04 Gut;Motorschalter Leerlauf Durchstarten
27.07.2026 16:39:04 Gut;Motorschalter Motor An
27.07.2026 16:39:13 Gut;Bank 2 geladen
27.07.2026 16:41:35;VBar Logfile End -- 27.07.2026 -- 16:41:34
27.07.2026 16:41:35 Gut;OMP Regler getrennt
27.07.2026 16:41:38;VStabi Start -- LOGO 200 -- 0027009595 -- V 8.2 -- pl 40
27.07.2026 16:41:38 Warn;RC Eingangspaket verloren
27.07.2026 16:41:39 Fehler;RC Failsafe aktiviert
27.07.2026 16:41:39 Gut;OMP Regler erkannt
27.07.2026 16:41:40 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:40 Info;Drehzahlregler ist am unteren Gaslimit
27.07.2026 16:41:41 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:45 Info;Drehzahlregler auf AUS geschaltet
27.07.2026 16:41:45 Info;Aus - Regler - Umin:11.0V Imax:8.4A Temp:34?
27.07.2026 16:41:45 Gut;Motorschalter Motor Aus
27.07.2026 16:41:46 Info;Drehzahlregler auf AN geschaltet
27.07.2026 16:41:46 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:46 Info;Aus - Regler - Umin:11.3V Imax:0.0A Temp:33?
27.07.2026 16:41:46 Gut;Motorschalter Motor An
27.07.2026 16:41:47 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:47 Info;Drehzahlregler auf AUS geschaltet
27.07.2026 16:41:47 Warn;Drehzahlregler auf Vollgas
27.07.2026 16:41:47 Gut;Motorschalter Motor Aus
27.07.2026 16:41:48 Gut;Bank 1 geladen
27.07.2026 16:44:43;VBar Logfile End -- 27.07.2026 -- 16:44:43
27.07.2026 16:44:44 Gut;OMP Regler getrennt
machine-translated from German · Show original