Jurrien Saelens
9 August 2025 14:2109.08.2025 14:21
Are there any improvements to the rear of the Logo 200 2025 V8?
I'm still flying my Logo 200 V6, but more and more pilots in my club are switching to the Goosky Max S2. I've flown it too, and the tail is simply much better than the Logo 200's.
Gibt es für den Logo 200 2025 V8 eine Verbesserung am Heck?
Ich fliege immer noch mit meinem Logo 200 V6, aber immer mehr Piloten in meinem Verein steigen auf den Goosky Max S2 um. Ich bin ihn auch schon geflogen, und das Heck ist einfach viel besser als beim Logo 200.
Eddi E. aus G.
11 August 2025 08:4511.08.2025 08:45
Good morning,
Yes, definitely. VBar EVO already has that, and the EVO micro will too.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
ja, auf jeden Fall. VStabi EVO hat das auch schon, und die EVO micro dann auch.
Grüßle
Eddi
Born to fly ...
forced to work.
Jurrien Saelens
11 August 2025 10:1111.08.2025 10:11
I find it somewhat strange to make this available for the large EVO gyro first. The "Tail Torque Extension" is really necessary, especially for smaller helicopters.
It's a shame that VBar is now lagging behind the competition, whereas it used to be far ahead.
Is there any chance this will be made available for the Neo Micro?
Because I still find VBar's swashplate control superior.
Ich finde es etwas seltsam, das zuerst für den großen EVO-Gyro verfügbar zu machen. Gerade bei den kleinen Hubschraubern ist die „Tail Torque Extension“ wirklich nötig.
Schade, dass VStabi jetzt hinter der Konkurrenz zurückliegt, während es früher immer weit voraus war.
Gibt es eine Chance, dass dies für den Neo Micro verfügbar gemacht wird?
Denn die Taumelscheibensteuerung von VStabi finde ich immer noch überlegen.
Eddi E. aus G.
11 August 2025 13:3811.08.2025 13:38
Hi,
To my knowledge, this will not be available for NEO (it cannot be, for technical reasons).
The EVO hardware can do that, and since the larger version was available first, it was developed and tested on that.
It also works on the 200mm version: remove it, shrink it, stick it on, and be happy :-)
I don't know if VBar is really behind the competition; I keep hearing (and seeing) completely different things.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
meines Wissens wird's das für NEO nicht geben (geben können, aus technischen Gründen).
Die EVO-Hardware kann das, und da die große zuerst da war, wurde es halt darauf entwickelt und getestet.
Geht ja auch auf dem 200-er, aushausen, einschrumpfen, drauf kleben, glücklich werden :-)
Ich weiß auch nicht, ob VStabi wirklich hinter der Konkurrenz zurück liegt, ich höre (und sehe) da immer wieder ganz andere Sachen ^^
Grüßle
Eddi
Born to fly ...
forced to work.
Jurrien Saelens
11 August 2025 15:4611.08.2025 15:46
Well, since it's still not available and other manufacturers have been offering it for years, it's fair to say that you're lagging behind in this area.
And to buy an EVO and completely rebuild it to put it on my already quite expensive Logo 200 seems a bit excessive to me, and only for people with too much money and time.
Edited once. Last edited on 11/08/2025 at 16:02 by Jurrien Saelens.
Na ja, da es immer noch nicht verfügbar ist und es bei anderen Herstellern schon seit Jahren möglich ist, kann man doch wohl sagen, dass ihr in diesem Bereich hinterherhinkt.
Und sich jetzt noch extra einen EVO zu kaufen und diesen dann komplett umzubauen, um ihn auf meine ohnehin schon recht teure Logo 200 zu setzen, finde ich doch ein bisschen übertrieben und nur für Leute mit zu viel Geld und Zeit.
1 mal bearbeitet. Zuletzt am 11.08.2025 16:02 von Jurrien Saelens.
Wingtip
11 August 2025 23:5311.08.2025 23:53
The suggestion to take off an Evo and stick it on an L200 is rather... let's say extreme.
An Evo, perhaps even with a Pro update, costs around €350 for an aging OMP M2. The 200 is no more than that.
At the beginning of the year I would have bought one if it had been available as a V8, as announced.
It's almost mid-August now - frustration is high, the desire is gone, and summer is also on its last legs.
Everyone!!! In my club, other micro helicopters are now flying and have even bought different transmitters for them. Myself included, and we're all quite happy with them.
It won't get you anywhere, but maybe you're interested in what's going on right outside your door, instead of everyone just waiting for Mikado.
Den Tipp ein Evo auszuziehen und auch noch auf einen L200zu kleben ist wohl etwas …ich sag mal heftig.
Ein Evo dann auch noch vielleicht mit Pro Update sind rund 350€ für einen in die Jahre gekommenen OMP M2. Mehr ist der 200er nicht.
Anfang des Jahres hätte ich mir noch einen gekauft wäre er den wie angekündigt als V8 lieferbar gewesen.
Inzwischen ist fast Mitte August - der Frust ist groß , die Lust ist weg und der Sommer auch in den letzte Zügen.
Alle !!! In meinem Verein fliegen inzwischen andere Micro Helis und haben dafür sogar andere Sender angeschafft. Mich eingeschlossen und wir sind alle soweit zufrieden.
Bringt euch nicht weiter, aber vielleicht interessiert es euch doch so was vor eurer Haustür abgeht und nicht alle nur auf Mikado warten.
Lennart
12 August 2025 08:2612.08.2025 08:26
I can only agree with Wingtip.
Da kann ich mich nur an Wingtip anschließen.
Zalo
13 August 2025 22:2313.08.2025 22:23
I completely agree with Wingtip. I'm seeing the same thing at my club. If they can't deliver as promised (they said the Logo 200 V8 would come with the V8 engine), they could at least explain why the situation is the way it is. I'm tired of checking the online shop and the forum every day only to be disappointed again. There are manufacturers who can deliver, even if they have a different name on the product.
Ich kann mich hier Wingtip nur anschließen. Ich beobachte das gleiche in meinem Verein. Wenn man dann schon nicht liefern kann wie angekündigt (es hieß ja der Logo 200 V8 kommt mit der V8) könnte man wenigstens kommunizieren warum die Situation so ist wie ist. Ich bin es leid jeden Tag in den Onlineshop und ins Forum zu schauen um jeden Tag erneut enttäuscht zu werden. Da gibt es Hersteller die können liefern, auch wenn ein anderer Name drauf steht.
Jurrien Saelens
6 September 2025 11:4806.09.2025 11:48
I also got myself a Goosky S2 Max, bound to my VBar Control Touch with an RX6.
It's great that the macro cells are now included as standard in the Goosky transmitter.
It flies really well!
I initially wanted to sell my Logo 200, but then I found another solution:
The VBar Neo Mini from the Logo 200 is now in the Eratix Shockflyer – and wow, this thing really takes off with VPlane + Gyro.
It's a shame the Mini VBar Neo was never available for individual purchase (or at least I thought it was), because it works incredibly well on such a small plane. Hopefully the EVO Mini will be released separately someday; then I might get it to convert my old Logo 200 to a V8.
Edited twice. Last edited on 06/09/2025 at 12:43 by Jurrien Saelens.
Hab mir jetzt auch einen Goosky S2 Max geholt, mit so einem RX6 an meinen VBar Control Touch gebunden.
Cool, dass die Makrozellen inzwischen standardmäßig für den Goosky im Sender drin sind.
Fliegt richtig gut!
Erst wollte ich meinen Logo 200 verkaufen, aber hab dann doch ’ne andere Lösung gefunden:
Die VBar Neo Mini vom Logo 200 steckt jetzt im Eratix Shockflyer – und wow, das Teil geht mit VPlane + Gyro echt ab.
Schade nur, dass es die Mini VBar Neo nie einzeln zu kaufen gab (zumindest dachte ich das), weil auf so einem kleinen Flieger funktioniert das einfach mega. Hoffentlich kommt die EVO Mini mal separat raus, dann hol ich mir die vielleicht, um meinen alten Logo 200 zum V8 umzubauen.
2 mal bearbeitet. Zuletzt am 06.09.2025 12:43 von Jurrien Saelens.
Reinhard_Bley@web.de
19 October 2025 11:3519.10.2025 11:35
Hi
Is it really that simple? You take a VBar Evo, select a new stup (logo 200) and fly off.
To explain, I bought a Logo 200 without a stabilizer. I then installed a Neo stabilizer. And I'm actually satisfied, apart from a few minor antics at the rear. But anyway, when the V8 software became available, I flashed an Evo version onto the Logo 200, but that was a complete disaster. I had to drastically reduce the values to prevent it from wobbling excessively. The settings for the rear motor were also completely off. So I left it and put the Neo back in. Could it be that the reason for my problems is, or was, the fact that the parameters for the Logo 200 hadn't been fully tested yet, since the V8 was only available for a few days at that point?
And yes, for all those who find it strange to fit a Neo or Evo into the Logo 200, it fits perfectly and the center of gravity is minimally front-heavy with a 750 mAh battery.
Greetings from southern Germany.
Reinhard B.
Hi
Ist es tatsächlich so einfach? Man nimmt eine VStabi Evo , wählt ein neues stup ( logo 200 ) und losfliegen.
Zur Erklärung ich habe einen Logo 200 ohne stabi gekauft. Hab dann eine Neo eingebaut. Und bin eigentlich zufrieden bis auf ein paar kleine Kapriolen die er am Heck macht. Aber egal , als die V8 Software verfügbar war habe ich eine Evo auf den logo 200 , das war aber eher ein Schuss in den Ofen. Ich musste die werte extrem runter nehmen damit der sich nicht zu Tode wobbelt. Auch die Einstellungen für den Heckmotor waren total daneben.. ergo ich habe es gelassen und das Neo wieder rein. Kann das sein dass der Grund für meine Probleme die noch nicht zu Ende getesteten Parameter für den Logo 200 sind oder waren , weil die V8 zu dem Zeitpunkt ja nur ein paar Tage erhältlich war.
Und ja für alle die das jetzt seltsam finden eine Neo oder Evo in den Logo 200 zu basteln , das passt super da rein und der Schwerpunkt ist minniminniminnimal kopflastig mit nem 750er Akku.
LG. Aus dem Süden von Deutschland.
Reinhard B.
Jurrien Saelens
20 October 2025 14:5220.10.2025 14:52
I recently came across this video in which a clever tinkerer built a simple “Tail Torque Extension” for the VBar Neo V6 Macrocells on the Logo 200 V6.
Unfortunately, I can no longer test it, as my VBar Neo Mini from the Logo 200 is now in the Eratix Shockflyer.
But if anyone is interested – here is the setup and video:
https://www.youtube.com/watch?v=ih13oCQ8gMA If this really works, it's somewhat strange that Mikado never officially released it for the V6 – it seems quite simple, and you can implement it yourself.
@Reinhard, thanks for your input.
Ich bin vor Kurzem auf dieses Video gestoßen, in dem ein schlauer Tüftler eine einfache „Tail Torque Extension“ für die VBar Neo V6 Macrocells auf der Logo 200 V6 gebaut hat.
Ich kann es leider nicht mehr testen, da mein VBar Neo Mini aus dem Logo 200 jetzt im Eratix Shockflyer steckt.
Aber falls jemand Interesse hat – hier ist das Setup und Video:
https://www.youtube.com/watch?v=ih13oCQ8gMA
Wenn das wirklich funktioniert, ist es etwas seltsam, dass Mikado das nie offiziell für die V6 herausgebracht hat – scheint eigentlich recht einfach zu sein, und man kann es selbst umsetzen.
@Reinhard, danke für deinen Input.
Reinhard_Bley@web.de
20 October 2025 18:1720.10.2025 18:17
You're welcome, but I don't know which input you mean.
Regarding my topic.
Yesterday I installed an Evo V8 motor in the Logo. What can I say? Perfect. I just adjusted the ESC at the tail and increased the left limit because the tail motor wasn't shutting off, and that was it. I tweaked the flight parameters a bit to suit my needs, and Eureka! It's like a brand new helicopter, unrecognizable. Another very positive result is the flight time, almost a minute longer. This is probably due to the tail, as it's significantly more stable and the motor has less work to do to return it to the correct position.
At 6000RPM at the head, the right limit at the rear needs to be slightly increased to get a little more power.
Installation information.
I removed the ESC from its housing, glued the Neo/Evo to the frame with 3M adhesive, and then slapped the ESC onto the stabilizer. With a 750mAh battery, I almost perfectly achieved the center of gravity. I think the Logo 200 is nose-heavy in its original configuration. But that's just a guess since mine was bought without a stabilizer.
Greetings
Reinhard B
Bitte gerne , aber ich weis nicht welchen Input du meinst.
Zu meinem Thema.
Ich hab gestern noch eine Evo V8 in den logo gebastelt . Was soll ich sagen perfekt. Am Heck ESC anpassen / linkslimmit erhöhen weil der Heckmotor nicht abschaltet das wars. Ein wenig die Flugparameter auf meine Bedürfnisse angepasst , Heureka wie ein neuer Heli nicht wieder zu erkennen. Ein sehr positives Ergebnis ist auch die Flugzeit ,fast eine Minute mehr. Wird wohl dem Heck geschuldet sein da es bedeutend stabiler ist und der Motor weniger Arbeit hat das Heck wieder auf Pos zu bringen.
Bei 6000RPM am kopf muss man das Rechtslimmit am Heck leicht erhöhen , damit ein wenig mehr Power drauf kommt.
Info zum Einbau.
Ich hab den Regler aus dem Gehäuse geholt , das Neo/Evo mit 3M auf den rahmen geklebt und den Regler oben aufs Stabi geklatscht. Somit habe ich mit nem 750er Akku den Schwerpunkt fast perfekt getroffen. Ich denke der Logo 200 ist in der Orginal Ausstattung Kopflastig. Ist aber nur eine Vermutung da meiner ohne Stabi gekauft wurde.
Grüße
Reinhard . B
Jurrien Saelens
20 October 2025 18:5820.10.2025 18:58
@Reinhard I just wanted to say thank you for your very interesting post!
Edited once. Last edited on 20.10.2025 at 19:12 by Jurrien Saelens.
@Reinhard Ich wollte einfach nur danke sagen für deinen sehr interessanten Beitrag!
1 mal bearbeitet. Zuletzt am 20.10.2025 19:12 von Jurrien Saelens.
Jurrien Saelens
24 October 2025 09:3024.10.2025 09:30
I've now converted mine to a V8 as well. It was one with standard servo connectors, so no disassembly or soldering was necessary. The only problem: the canopy no longer fits. Luckily, the canopy from the Goosky S2 Max (also 10 grams lighter) fits perfectly over the larger gyro. An added bonus: I can change the LiPo battery without removing the canopy.
The software was a bit tricky:
Evo was still on V7 when I received it this week.
I initially used the Logo-200 setup -> it worked, but I wanted V8.
Upgraded to V8 Pro.
Then a huge wobble, almost crashed…
Then I completely reinstalled the Logo-200 -> the rear camera stopped working because DSHOT was active.
Set to the correct setting and limit set to 104, otherwise the rear end would have continued to spin.
Now he flies great.
Edited 4 times. Last edited on 25.10.2025 at 12:29 by Jurrien Saelens.
Habe meinen jetzt auch auf V8 umgebaut. War einer mit normalen Servosteckern, also kein Ausbauen/ Löten nötig. Einziges Problem: die Haube passt nicht mehr. Zum Glück passt die Haube vom Goosky S2 Max (auch 10 Gramm leichter) perfekt über das größere Gyro. Extra-Vorteil: Lipo-Wechsel ohne Haube abnehmen.
Software war etwas tricky:
Evo war noch auf V7, als ich sie bekommen habe diese Woche.
Erst das Logo-200 Setup genommen -> lief, aber ich wollte V8.
Upgrade auf V8 Pro gemacht.
Danach mega Wobble, fast gecrasht…
Dann Logo-200 nochmal komplett neu installiert -> Heck ging nicht mehr, weil DSHOT aktiv war.
Auf richtige Einstellung gestellt und Limit auf 104 gesetzt, sonst hat das Heck weitergedreht.
Jetzt fliegt er top.
4 mal bearbeitet. Zuletzt am 25.10.2025 12:29 von Jurrien Saelens.
Reinhard_Bley@web.de
26 October 2025 10:1926.10.2025 10:19
@Jurrien
Hi ..
If you take the controller out of the housing and then glue it onto the stabilizer, the center of gravity will be correct.
I use Gens 750 batteries, which makes it slightly top-heavy. The original canopy also fits back on.
Since the new Logo 200V8 arrived in my mailbox last Thursday, I have a comparison. Original V8 and converted to V8.
I fly fairly aggressive 3D, but I'm definitely a pro. Even so, I notice small differences. The new ESC has absolutely clean and precise tail control. The difference isn't extreme compared to my own custom-built V8. The swashplate servos are also powered by 6 volts (which can be increased, but I don't yet have information on what the servos can actually handle), and there's a slight difference there as well. In conclusion, up to 5200 RPM I don't notice any significant difference; only above 5800 RPM does the new ESC have an advantage. (This is just my observation as a non-professional).
At 6000 RPM and with the original parameters, both were incredibly fun. But the original V8 has the advantage at that RPM. You can definitely feel a significant difference.
It would be silly if there were no improvement.
One thing is clear to me: since the Vbar came out, I don't want any other transmitter and I'm completely satisfied with it; no Goosky or OMP will ever enter my house in their original form. Why install a satellite receiver in a helicopter when I have the best system?
What I've always found a bit of a shame (with all manufacturers) is that tests and reports are almost always only from extreme pilots. But the average consumer, for the most part, just enjoys flying.
Regards, RB
@Jurrien
Hi ..
Wenn du den Regler aus dem Gehäuse holst und den dann auf das Stabi klebst , passt der Schwerpunkt .
Ich verwende Gens 750er Akkus, damit ist er minimal kopflastig. Auch die Original Haube passt dann wieder drauf.
Da am vergangenen Donnerstag der neue Logo 200V8 im Briefkasten war , habe ich einen Vergleich. Original V8 und umgebaut auf V8.
Ich fliege relativ knackiges 3D , bin aber mit Sicherheit voll Profi. Aber dennoch merke ich kleine unterschiede. Der neue Regler hat das Heck absolut sauber und exakt im Griff. Der Unterschied ist aber nicht extrem zum Eigenbau V8. Auch die TS Servos werden mit 6 Volt versorgt ( kann erhöht werden hab aber noch keine Info was die Servos tatsächlich aushalten ) auch da ist ein kleiner Unterschied zu spüren. Das Fazit bis 5200RPM merke ich keinen nennenswerten Unterschied erst ab 5800RPM ist der neue Regler im Vorteil. ( das ist nur meine Erkenntnis als nicht Profi).
Bei 6000RPM und den Originalen Parameter machten beide Laune ohne Ende. Aber der Original V8 ist bei der Drehzahl im Vorteil. Da merkt man doch einen nennenswerten Unterschied.
Währe ja doch doof wenns keine Verbesserung geben würde.
Für mich ist eins klar , da ich seit es die Vbar gibt keinen anderen Sender haben will und ich absolut zufrieden bin, kommt kein Goosky oder OMP im original ins Haus. Warum einen Sat oder Empfänger in einen Heli bauen wenn ich das beste System habe.
Was ich immer schon ein wenig schade find ( bei allen Herstellern ) das es Tests und die berichte dazu immer nur von Extrem Piloten gibt. Aber der Endverbraucher zum größten teil einfach nur Spaß am fliegen hat.
Lg. R.B.
Jurrien Saelens
26 October 2025 11:1526.10.2025 11:15
Reinhard_Bley@web.de wrote:
-------------------------------------------------------
>
One thing is clear to me, since the Vbar...
There is no other channel I want and I
I am absolutely satisfied; no Goosky or OMP is needed.
> in the original house. Why a satellite or
> Build a receiver in a helicopter if I want the best
> I have a system.
>
Yes, I have the same issue. I just think it's a real shame that Mikado never solved the problem with the rear end breaking loose on the V6. That was also the reason why I got a Goosky, to see if this "Tail Torque Extension" actually makes a difference. And yes, it actually does.
Now, after four years, Mikado has finally realized this, so we can move forward again. As I wrote in my previous post: In my opinion, Mikado always had the best algorithm on the swashplate, but the Logo 200 was simply really bad on the tail.
And hopefully Mikado will also release the V8 Mini and a software setup for the Goosky S2 Max. Then I'll try the V8 Mini on the Goosky too. It definitely has significantly more power than the old OMP.
Edited twice. Last edited on 26.10.2025 at 12:06 by Jurrien Saelens.
Reinhard_Bley@web.de schrieb:
-------------------------------------------------------
>
> Für mich ist eins klar , da ich seit es die Vbar
> gibt keinen anderen Sender haben will und ich
> absolut zufrieden bin, kommt kein Goosky oder OMP
> im original ins Haus. Warum einen Sat oder
> Empfänger in einen Heli bauen wenn ich das beste
> System habe.
>
Ja, das ist bei mir auch so. Ich finde es nur wirklich schade, dass Mikado das Problem mit dem ausbrechenden Heck bei der V6 nie gelöst hat. Das war auch der Grund, warum ich mir einen Goosky geholt habe, um zu sehen, ob diese „Tail Torque Extension“ wirklich etwas bringt. Und ja, das funktioniert tatsächlich.
Jetzt hat Mikado das endlich nach 4 Jahren eingesehen, also können wir wieder weitermachen. Wie ich in meinem vorherigen Post schon geschrieben habe: Auf der Taumelscheibe hatte Mikado meiner Meinung nach schon immer den besten Algorithmus, aber auf dem Heck war die Logo 200 einfach richtig schlecht.
Und hoffentlich bringt Mikado auch die V8 Mini und ein Software-Setup für den Goosky S2 Max raus. Dann packe ich die V8 mini auch mal auf den Goosky. Der hat echt deutlich mehr Power als der alte OMP.
2 mal bearbeitet. Zuletzt am 26.10.2025 12:06 von Jurrien Saelens.
thomas1130
26 October 2025 14:0526.10.2025 14:05
Jurrien Saelens wrote:
-------------------------------------------------------
I've now converted mine to a V8 as well. It was one
> with standard servo connectors, so no removal/
Soldering required. Only problem: the hood doesn't fit.
> not anymore. Luckily, the Goosky hood fits.
> S2 Max (also 10 grams lighter) fits perfectly over the
Larger gyro. Extra advantage: Lipo replacement without
Remove the hood.
Thanks for the great report :-)
That sounds very interesting, as I also have an "old" one with servo connectors 8-)
I'll have to take a closer look at that – because I actually like the "little dwarf" – it's just that the rear end is a REAL weak point on the old one...
Best regards,
Thomas
Jurrien Saelens schrieb:
-------------------------------------------------------
> Habe meinen jetzt auch auf V8 umgebaut. War einer
> mit normalen Servosteckern, also kein Ausbauen/
> Löten nötig. Einziges Problem: die Haube passt
> nicht mehr. Zum Glück passt die Haube vom Goosky
> S2 Max (auch 10 Gramm leichter) perfekt über das
> größere Gyro. Extra-Vorteil: Lipo-Wechsel ohne
> Haube abnehmen.
Danke für den super Bericht :-)
das kling sehr interessant, da ich auch noch einen "alten" mit Servosteckern habe 8-)
Muss ich mir mal näher ansehen - denn eigentlich mag ich den "kleinen Zwerg" - nur das Heck ist halt eine ECHTE Schwachstelle beim alten..
LG,
Thomas
Reinhard_Bley@web.de
26 October 2025 15:5426.10.2025 15:54
Hi…
This is what it looks like when the old little car gets a VBar Neo and the ESC is mounted on the stabilizer. And they're 750 Gens, and the center of gravity is correct.
Regards, RB
Hi …
So sieht das ganze aus , wenn der alte kleine ein VStabi Neo bekommt und der Regler auf der Stabi sitzt. Und es sind 750er Gens und der Schwerpunkt passt.
Lg. R.B
Jurrien Saelens
26 October 2025 17:0126.10.2025 17:01
This is what it looks like on my Goosky hood, with two new holes. The hood is now operating in double shifts.
Edited once. Last edited on 26.10.2025 at 17:12 by Jurrien Saelens.
So sieht es bei mir aus mit der Goosky-Haube, mit zwei neuen Löchern. Die Haube ist jetzt im Doppelschicht-Betrieb.
1 mal bearbeitet. Zuletzt am 26.10.2025 17:12 von Jurrien Saelens.
Reinhard_Bley@web.de
26 October 2025 19:1126.10.2025 19:11
HI
Yes, that fits perfectly.
At least your controller is cooled.
Regards, RB
HI
Ja das passt doch.
Zumindest ist dein Regler gekühlt.
Lg. R.B
Zalo
12 November 2025 22:5612.11.2025 22:56
Hi,
I'm trying to pair a Vstabi Evo with the old (not the V8) ESC, but I just can't get the rear motor to work. Could someone tell me the correct settings? Thanks!
Hi,
ich versuche gerade eine Vstabi Evo mit dem alten (nicht den V8) Regler zu verheiraten, ich bekomme den Heckmotor einfach nicht zum laufen, kann mir jemand die korrekten Einstellungen verraten? Liebe Grüße
Jurrien Saelens
13 November 2025 08:2713.11.2025 08:27
500Hz 1500 1520uS
Remove all rotor blades, because the motor will start to spin if the limiter is not set correctly!
500Hz 1500 1520uS
Alle Rotorblätter entfernen, denn der Motor beginnt sich zu drehen, wenn die Begrenzung nicht richtig eingestellt ist!
Jurrien Saelens
12 October 2026 19:3412.10.2026 19:34
I just updated from 8.2.8 to 8.2.11, and now the rear end is oscillating at a high frequency.
I really regret the update, because my old helicopter flew very well with version 8.2.8.
I was unaware that such a small bug fix update would bring about such big changes.
Is there a way to revert back to version 8.2.8?
Ich habe gerade von 8.2.8 auf 8.2.11 aktualisiert, und jetzt pendelt das Heck hochfrequent.
Ich bereue das Update wirklich, denn mit 8.2.8 flog mein alter Heli sehr gut.
Mir war nicht bewusst, dass ein so kleines Bugfix-Update so große Änderungen mit sich bringen würde.
Gibt es eine Möglichkeit, wieder auf 8.2.8 zurückzugehen?
Eddi E. aus G.
13 October 2026 09:0113.10.2026 09:01
Good morning,
No, there's no going back.
Did you just update, or did you change anything else?
—Eddi
Born to fly ...
forced to work.
Moin,
nee, einen Weg zurück gibt es nicht.
Hast Du nur upgedated, oder sonst noch was verändert?
—Eddi
Born to fly ...
forced to work.
Jurrien Saelens
13 October 2026 12:3713.10.2026 12:37
I only performed the update.
The settings are still exactly the same as last year:
https://www.vstabi.info/forum/read.php?32,208884,208899#msg-208899 If I significantly reduce the tail sensitivity, it gets a little better, but the helicopter is not really flyable.
Edited twice. Last edited on 13.10.2026 at 18:13 by Jurrien Saelens.
Ich habe nur das Update durchgeführt.
Die Einstellungen sind immer noch genau wie letztes Jahr:
https://www.vstabi.info/forum/read.php?32,208884,208899#msg-208899
Wenn ich die Heckempfindlichkeit deutlich reduziere, wird es etwas besser, aber der Heli ist nicht wirklich fliegbar.
2 mal bearbeitet. Zuletzt am 13.10.2026 18:13 von Jurrien Saelens.