baane
8 August 2015 01:2508.08.2015 01:25
I have a small 3d plane that has full length ailerons with a servo on each wing. I want to setup flaperons, but don't see anything obvious. I have flown the plane with a lot of success setup normal. Setting it up with the flaps option is not working as I want.
I want to be able to flip a switch or turn a pot and the ailerons re-center down 20 degrees or so. I also want to mix the elevator into the ailerons so that they both go down with up elevator and vice versa.
Anyone that has done this setup have and tips?
Thanks,
Brian
baane
8 August 2015 02:2308.08.2015 02:23
Figured out how to use the macrocells to set the flap channel then use the expert mixers to put the mix on a switch.
Any way to make this bankable? I would like to have a bank that mixes elevator to flap and one that does not.
RV
8 August 2015 07:3208.08.2015 07:32
Quote:Any way to make this bankable? I would like to have a bank that mixes elevator to flap and one that does not.
Yes of course.
For fully understanding - please add the current VPlane AND the Makrocells Setup (must be stored seperately) in a zip file.
I'll have a look and post a example ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
baane
8 August 2015 23:2108.08.2015 23:21
thanks for looking. Another item I can't get working is the talking telemetry on the countdown timer for planes. Works fine on my helis.
Dateianhänge:
öffnen |
Download -
Std2.zip
(548 bytes)
RV
10 August 2015 11:5310.08.2015 11:53
You have been on the right track. One possible soultion for such things is always use the flap option - if a plane has no flaps.
Here is my guide:
Switch handling or pot handling - input cell:
Assign the "Flap" cell#9 (channel cell) to the switch or pot which you want to use. As it should work on one side of the throw only - set limit and throw to 0 on the lower end - and enter 50 as center. Some delay would be useful too. Witch a switch you have now a "off", "Half" and "full" flaperon position. Using a pot - it is assigned to one half of the throw. switch or Pot direction can be changed by reversing here.
In the Flight mixers ch2 and 3 set up the flap maximum throw and direction (as you already did)
In the Flight mixer ch1 - here add the elevator partt with the flap mixer ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
10 August 2015 11:5610.08.2015 11:56
here the screenshots - very straight ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Dateianhänge:
öffnen |
Download -
Pictures.zip
(3.4 KB)
baane
11 August 2015 23:0811.08.2015 23:08
Thanks! I did manage to figure out how to mix the elevator into the ailerons like I wanted. I think I can set up a macrocell to be a switch for the banks. Other than that the bank switch does not seem to affect the settings.