nickwap
23 August 2015 17:4423.08.2015 17:44
This is the setup
VBControl
Neo with Vbar Link
V Plane Gas Motor.
Trying to set up the following.
Ignition Kill Switch to activate when 'Motor Off' and another Switch so that I would need Motor Run or Motor Idle and the, ignition to be armed to start.
Aux Channel for Smoke System ON/OFF and a mix Throttle as Master Smoke Channel as Slave to reduce smoke oil flow at low throttle settings.
I could do this with a JR in 10mins, but I want to uses my VBC :-)
Can any body help,
I have read the Macrocells App guide but i'm struggling :-(
Nick
RV
23 August 2015 22:1423.08.2015 22:14
Quote:
Ignition Kill Switch to activate when 'Motor Off' and another Switch so that I would need Motor Run or Motor Idle and the, ignition to be armed to start.
Seriously?
Does the ignition have a servo channel to turn on/off?
Please answer - and i'll try it this week ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nickwap
24 August 2015 19:0724.08.2015 19:07
Hi, Yep but not a servo,
I have an ignition kill module, it is fitted between the Ignition unit and the battery for the ignition, I would like the following functionality.
I have managed to set up AUX 1 to operate from a Switch to enable me to arm the Ignition.
I want to have this.
Motor OFF and Ignition in ANY Position = Motor OFF and Ignition OFF
Motor IDLE and Ignition on = Motor Idle
Motor RUN and Ignition on = Motor Run
PART 2
Smoke System
I have Aux 2 Set to a switch and will operate the Sullivan Smoke Pump I have reduced the rate to give me the required flow rate.
I now need to Mix throttle to Aux 2 so that Throttle below say 50% reduces the flow Rate and at Idle stops it altogether when the Smoke (AUX2) is on
Link to the Kill switch
http://www.apexmodels.com/gbu0-prodshow/EVOL-EVOA100.html?gclid=Cj0KEQjwgeuuBRCiwpD0hP3Cg4kBEiQAHflm1kMy7a65XAniADVvYcQCJMh8yXuV2VVKx7H6dWBfpJAaAhoa8P8HAQ
RV
24 August 2015 21:1624.08.2015 21:16
Will come back on this tomorrow - have some ideas but too late here ;-(
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
25 August 2015 20:3225.08.2015 20:32
Here we go ...
http://www.vstabi.info/en/node/2035
(Video example for this files)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Dateianhänge:
öffnen |
Download -
Setup1.zip
(6.6 KB)
MH
25 August 2015 22:2625.08.2015 22:26
nickwap
26 August 2015 08:0226.08.2015 08:02
This is excellent, I need to replicate this on my set up.
Thanks !!!!!
Nick
RV
26 August 2015 08:4426.08.2015 08:44
Just download the zip file above - and load the macrocells on your VBar through VBar Control and the macrocells folder - or dial in with the screenshots ;-)
Let me know ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
26 August 2015 19:2326.08.2015 19:23
German Video:
http://www.vstabi.info/de/node/2036
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nickwap
26 August 2015 20:4326.08.2015 20:43
Hi Rainer,
This is very good and I have learnt a lot about Macrocells, very powerful.
I have replicated your setup with the screen shots and I have most of the functions.
I cannot work out the ignition programming.
i think it is because I have different switch assignments to you.
How can I overcome this?
I have the following
From the rear left of the VBC to the Rear Right
1. Option 1 (I want to use this for smoke)
2. Bank Switch
3. Option 2
4. Pot 1 (Not used)
5. Pot 2 (Not used)
6. Option 3 (I want to used this for the ignition)
7. Motor
8. Security (Par Lock Off)
This is similar to the JR9503 that I also have.
I have been using this configuration with Nitro and Electric Helis and it feels very natural.
On the ignition set up, I need to be able to crank the motor with full throttle and no ignition to prime the motor, this is why I need a separate ignition switch.
The ignition need to be OFF whenever the motor switch is set to off , and ON in idle and run
Smoke also needs to be OFF when Motor is Off or Idle
Thanks for the support
Nick
RV
26 August 2015 21:0426.08.2015 21:04
Quote:On the ignition set up, I need to be able to crank the motor with full throttle and no ignition to prime the motor, this is why I need a separate ignition switch.
OK i understand.
Quote:The ignition need to be OFF whenever the motor switch is set to off , and ON in idle and run
So the throttle should not shut down when ignition is off?
In this case - just remove the security switch in Local switches, set it up as on/normal/active - or - assign it to another one for your own safety.
Quote:Smoke also needs to be OFF when Motor is Off or Idle
Use the curve ... and set it flat at the bottom unless you get the throttle opeening for "smoke on"
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
2 mal bearbeitet. Zuletzt am 26.08.2015 21:07 von RV.
RV
4 September 2015 23:1604.09.2015 23:16
NEW TASK: Add Flaperon in Bank2 and 3 - with a extra switch.
Output as channel on Ch2 and 3. General throw and direction, trim and failsafe is set up here.
Output cells are driven by Cell 30
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
2 mal bearbeitet. Zuletzt am 05.09.2015 08:57 von RV.
RV
4 September 2015 23:2204.09.2015 23:22
Cell 30 does the mixing of the flight control (Aileron) and the additional Flaperon
Cell 31 is there to add a delay in the flaperon switch for soft movement
Cell 32 defines the input for cell 31 in dependencie to the bank switch
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
4 September 2015 23:2404.09.2015 23:24
Cell 33 defines the flaperons in dependencie to the option 2 switch
Cell 34 is used in case of Bank 1 here as fixed value for "off"
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nickwap
5 September 2015 17:3605.09.2015 17:36
RV
5 September 2015 19:0605.09.2015 19:06
:-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.