← Cafe

Vbar neo translated

Public Talk › Cafe · Started by linken98 on 19 February 2026 20:4019.02.2026 20:40
linken98 19 February 2026 20:4019.02.2026 20:40
Hi, I read there are two different Neo versions, but I'm still confused. Can someone help me?
Old EVO with ICM-20649: Yes
New EVO with BMI088: No

What is what, do I need it for my OMP helicopter? Thanks.
machine-translated from German · Show original
RV 19 February 2026 21:3519.02.2026 21:35
Are we talking about VBar EVO or VBar NEO?

In the title you ask about 2 NEO versions - but in the text you ask about 2 EVOs.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
linken98 20 February 2026 10:3220.02.2026 10:32
To use vstabi evo
machine-translated from German · Show original
Eddi E. aus G. 20 February 2026 12:1120.02.2026 12:11
Good morning,

In early 2023, the first generation of rear sensors was released whose rear sensor reacted erratically to certain frequencies (2+ kHz range) and under high mechanical load.
Also, twitchy.
As in, Heck suddenly jerks away.

However, this did not always occur with every type of helicopter; there were also plenty of pilots who had no problems at all.

From around October 2023, a different sensor will be used that does not have this effect.
Serial numbers (with a gray area around the turn of the millennium... if in doubt, please inquire!) approximately > 27002000.

The first generation could and still can be 'fixed' by generously potting the sensor (sealing it airtight and simultaneously mechanically damping and detuning it; this is not an unknown or unusual procedure in electrical engineering or electronics).
The good old hot glue proved to be the weapon of choice; anything else would have been too messy or too permanent (silicone, epoxy), and special potting compound for electronics is rarely readily available when you actually need it.
From serial number 27001270 onwards, they were already potted at the factory – but keep your eyes open when buying used, you never know what might have happened in between.

./.

OMP Heli is a bit 'vague' right now :-) ... which one is it for?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
linken98 20 February 2026 16:3820.02.2026 16:38
Thank you very much.

Is the OMP M7R compatible? Can you install rubber buffers and a metal plate to dampen vibrations? Some people fly with the buffers, but many fly without them. Hence the question above: with the old one, without? Can I find the serial number on the packaging or in my account?

Best regards
machine-translated from German · Show original
Eddi E. aus G. 23 February 2026 09:3423.02.2026 09:34
Good morning,

The serial number, in the account, or if the VBar is connected to the transmitter, model status.

The purpose of rubber buffers and weights is to decouple the helicopter's vibration frequencies from the sensors (or vice versa), essentially detuning the system so that resonances don't become problematic. That is, if that's the case. Not every "identical" helicopter behaves the same.

The frequencies to which the first EVO reacted so erratically could also be transmitted (acoustically) through the air.
Big speaker, amplifier with sufficient power, frequency generator, hearing protection (!), and if you hit the not-so-sweet spot, –bam–.
That's why (airtight) potting is necessary.

As far as the gyros (normal flight control) are concerned, the buffer and weight are usually uncritical.
If rescue functions (acceleration sensors) are to be used, the situation can become critical earlier. SAB, for example, recommended – after introducing the 4-gyroscope platform option – that it should definitely be used in stabilization systems with a rescue function.

However, you can also determine this quite easily and relatively reliably yourself: fly without the rescue system (in such a way that you wouldn't need it!), leave the rescue status screen on the transmitter open, and, for example, hover every minute and check: the ball should return to the center of the crosshairs (or almost), and the flight attitude should be displayed correctly. If this is still the case after a battery charge at high speed and under more power, then everything should be safe. "Should be," because things can always change slightly due to further wear and tear, break-in, etc.
I keep hearing that, but the last 100, 200, 500, 1,000 flights were all normal.
Yes, ... but that doesn't mean that even without a crash or anything else, there is no wear and tear.

Otherwise, try adjusting the damping and, if necessary, using a detuning weight.

Things would get even more interesting with nitro cars, especially with the acceleration sensors.

With the first generation of VBar, this wasn't the norm either, but it occurred more frequently, and we reacted.
In retrospect, I would say that the majority simply functioned as intended; the public reactions painted an exaggerated picture.
However, I don't want to downplay it; every critical situation (more frequent in the subset) or every crash (thankfully less frequent) as a consequence is one too many!

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless