Hello everyone,
I recently bought the Goosky RS6, but for the past two months I've been tinkering with it because I can't get the tailwag out. I've never had this problem with any other helicopter.
Runs on VBar V8 with the Control Touch.
Slider free-running without hook
Tail servo: KST X20-1035 HLS V3.0 set to 760µs/1000Hz instead of the 560Hz specified by KST. Changing the frequency to 500Hz also makes no difference; no noticeable change is seen.
The servo arm is set to 90 degrees using the KST Toolbox. When mechanically adjusting the reverse rotation in the setup wizard, I set it to 2-3 degrees, but when exiting the wizard, the angle increases to around 8 degrees. I have no idea what this means (photos attached). Why does the servo jump when changing modes?
The difference in the endpoint values also seems too large to me?! I didn't see this with the other models.
The analyzer shows no significant vibrations.
Adjust the belt tension so that you can still push the belt through.
Ball joint of the tail servo arm, as per the instructions, 18mm from the center point.
I can adjust gain values from 50 to 110 or even higher without any change to the pendulum motion.
My experience doesn't extend beyond this point, so I can't find out any further what causes the WAG.
Thanks in advance for any help!
Greeting,
Marc
I recently bought the Goosky RS6, but for the past two months I've been tinkering with it because I can't get the tailwag out. I've never had this problem with any other helicopter.
Runs on VBar V8 with the Control Touch.
Slider free-running without hook
Tail servo: KST X20-1035 HLS V3.0 set to 760µs/1000Hz instead of the 560Hz specified by KST. Changing the frequency to 500Hz also makes no difference; no noticeable change is seen.
The servo arm is set to 90 degrees using the KST Toolbox. When mechanically adjusting the reverse rotation in the setup wizard, I set it to 2-3 degrees, but when exiting the wizard, the angle increases to around 8 degrees. I have no idea what this means (photos attached). Why does the servo jump when changing modes?
The difference in the endpoint values also seems too large to me?! I didn't see this with the other models.
The analyzer shows no significant vibrations.
Adjust the belt tension so that you can still push the belt through.
Ball joint of the tail servo arm, as per the instructions, 18mm from the center point.
I can adjust gain values from 50 to 110 or even higher without any change to the pendulum motion.
My experience doesn't extend beyond this point, so I can't find out any further what causes the WAG.
Thanks in advance for any help!
Greeting,
Marc
Hallo zusammen,
Ich habe mir den Goosky RS6 zugelegt, habe aber seit 2 Monaten nur herumtüfteln, da ich das Tailwag nicht herausbekomme. Bei keinem anderen Heli hab ich bis jetzt solche Probleme damit gehabt.
Läuft auf VStabi V8 mit der Control Touch.
Schieber freiläufig ohne Haken
Heckservo: KST X20-1035 HLS V3.0 eingestellt auf 760us/1000Hz anstatt 560Hz wie von KST vorgegeben. Frequenz auf 500Hz ändern hilft auch nichts, keine auffällige Veränderung zu sehen.
Servoarm per KST Toolbox auf 90 Grad eingestellt. Beim mechanischen einstellen des Gegenlaufs im Setup Assistenten stelle ich die 2-3 Grad ein, beim verlassen des Assistenten wird der Winkel allerdings größer, um die 8 Grad. Keine Ahnung was das bedeutet (Fotos im Anhang). Wieso springt das Servo beim Wechseln des Modus?
Der Unterschied in den Werten der Endpunkte scheint mir auch zu groß zu sein?! Habe ich bei den anderen Modellen nicht.
Analyzer zeigt keine nennenswerte Vibrationen an.
Riemenspannung, so dass man den Riemen noch durchdrücken kann.
Kugelkopf des Heckservoarm, wie in der Anleitung auf 18mm zum Mittelpunkt.
Gainwerte kann ich von 50 bis 110 oder sogar noch höher einstellen ohne irgendeine Veränderung am Pendeln.
Weiter reicht meine Erfahrung nicht um noch weiter herauszufinden, was den Wag verursacht.
Danke im Voraus für jegliche Hilfe!
Gruß,
Marc
Ich habe mir den Goosky RS6 zugelegt, habe aber seit 2 Monaten nur herumtüfteln, da ich das Tailwag nicht herausbekomme. Bei keinem anderen Heli hab ich bis jetzt solche Probleme damit gehabt.
Läuft auf VStabi V8 mit der Control Touch.
Schieber freiläufig ohne Haken
Heckservo: KST X20-1035 HLS V3.0 eingestellt auf 760us/1000Hz anstatt 560Hz wie von KST vorgegeben. Frequenz auf 500Hz ändern hilft auch nichts, keine auffällige Veränderung zu sehen.
Servoarm per KST Toolbox auf 90 Grad eingestellt. Beim mechanischen einstellen des Gegenlaufs im Setup Assistenten stelle ich die 2-3 Grad ein, beim verlassen des Assistenten wird der Winkel allerdings größer, um die 8 Grad. Keine Ahnung was das bedeutet (Fotos im Anhang). Wieso springt das Servo beim Wechseln des Modus?
Der Unterschied in den Werten der Endpunkte scheint mir auch zu groß zu sein?! Habe ich bei den anderen Modellen nicht.
Analyzer zeigt keine nennenswerte Vibrationen an.
Riemenspannung, so dass man den Riemen noch durchdrücken kann.
Kugelkopf des Heckservoarm, wie in der Anleitung auf 18mm zum Mittelpunkt.
Gainwerte kann ich von 50 bis 110 oder sogar noch höher einstellen ohne irgendeine Veränderung am Pendeln.
Weiter reicht meine Erfahrung nicht um noch weiter herauszufinden, was den Wag verursacht.
Danke im Voraus für jegliche Hilfe!
Gruß,
Marc
machine-translated from German · Show original