Hey everyone,
A suggestion for an extension/app:
The helicopter has its rotor blades folded and is either sitting on a shelf or hanging on the wall. Now they want to check something in the VBAR.
So, unpack the helicopter, clear the table, unfold the rotor blades. Turn on the helicopter/VBAR and check something. Then fold the rotor blades back in, pack the helicopter away, and put it on the shelf/hang it on the wall.
(If the helicopter is mounted on the wall, you only need to remove the blade caddy)
Just like that... half an hour gone...
Apologize to the woman: "I just wanted to pop in for a minute, but..." :-)
My idea:
An app that deactivates the servos based on the safety switch (i.e., only on the VBC).
The safety switch is there because it only allows the motor to run in the "open" position.
For this to work, the safety switch, as with a latch macro cell, must ALWAYS be switched to this position first.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Edited 1 time(s). Last edit at 09/20/2026 01:06PM by JMalberg.
A suggestion for an extension/app:
The helicopter has its rotor blades folded and is either sitting on a shelf or hanging on the wall. Now they want to check something in the VBAR.
So, unpack the helicopter, clear the table, unfold the rotor blades. Turn on the helicopter/VBAR and check something. Then fold the rotor blades back in, pack the helicopter away, and put it on the shelf/hang it on the wall.
(If the helicopter is mounted on the wall, you only need to remove the blade caddy)
Just like that... half an hour gone...
Apologize to the woman: "I just wanted to pop in for a minute, but..." :-)
My idea:
An app that deactivates the servos based on the safety switch (i.e., only on the VBC).
The safety switch is there because it only allows the motor to run in the "open" position.
For this to work, the safety switch, as with a latch macro cell, must ALWAYS be switched to this position first.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Edited 1 time(s). Last edit at 09/20/2026 01:06PM by JMalberg.
Moin Leute,
ein Vorschlag für eine Erweiterung/App:
Der Heli hat die Rotorblätter eingeklappt und steht im Regal oder hängt an der Wand. Jetzt will man etwas in der VBAR überprüfen.
Also Heli "auspacken", Tisch frei räumen, Rotorblätter ausklappen. Heli/VBAR einschalten und irgendwas nachgucken. Dann wieder Rotorblätter einklappen, Heli "einpacken" und ins Regal stellen / an die Wand hängen.
(Hängt der Heli an der Wand muss man nur den Blatt-Caddy abmontieren)
Zack ... 1/2-Stunde rum ...
Bei der Frau entschuldigen "Ich wollte nur mal kurz, aber ..." :-)
Meine Idee:
Eine App die anhand des Sicherheitsschalters (also nur auf der VBC), die Servos deaktiviert.
Der Sicherheitsschalter deshalb weil der nur in Stellung "Offen" den Motor an lässt.
Dazu muss der Sicherheitsschalter wie bei einer Latch-Makrozelle IMMER zuerst in diese Position geschaltet werden.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
Edited 1 time(s). Last edit at 09/20/2026 01:06PM by JMalberg.
ein Vorschlag für eine Erweiterung/App:
Der Heli hat die Rotorblätter eingeklappt und steht im Regal oder hängt an der Wand. Jetzt will man etwas in der VBAR überprüfen.
Also Heli "auspacken", Tisch frei räumen, Rotorblätter ausklappen. Heli/VBAR einschalten und irgendwas nachgucken. Dann wieder Rotorblätter einklappen, Heli "einpacken" und ins Regal stellen / an die Wand hängen.
(Hängt der Heli an der Wand muss man nur den Blatt-Caddy abmontieren)
Zack ... 1/2-Stunde rum ...
Bei der Frau entschuldigen "Ich wollte nur mal kurz, aber ..." :-)
Meine Idee:
Eine App die anhand des Sicherheitsschalters (also nur auf der VBC), die Servos deaktiviert.
Der Sicherheitsschalter deshalb weil der nur in Stellung "Offen" den Motor an lässt.
Dazu muss der Sicherheitsschalter wie bei einer Latch-Makrozelle IMMER zuerst in diese Position geschaltet werden.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
Edited 1 time(s). Last edit at 09/20/2026 01:06PM by JMalberg.
machine-translated from German · Show original