Volker Wahlen
15 March 2025 14:1115.03.2025 14:11
Hello :-)
I flew today; it's called Ediction.
The designer was present, as was the pilot. He flew Dreamliners until retirement.
I, the owner, am watching.
The trim was great, but something was wrong with the expo.
Even at 100, not much happened, as the two had expected.
Slow rise of the flaps, eventually followed by faster movement.
I disconnected the setup there.
Does another parameter need to be adjusted for the expo to take effect?
My plane is production number 38.
They all want me to use my Futaba transmitter, but I don't want to.
Not because it's bad, but I want to show that it's possible with it too.
All English, tough situation.
Please take a look and see what's wrong.
You can see that if I slowly adjust the altitude or whatever, there is no acceleration.
You can see it on the helicopter.
I see I can't help with the setup right now. Maybe tomorrow.
Greetings from sunny Thailand
Volker
Hallo :-)
heute den Flieger geflogen, nennt sich Ediction.
Der Erbauer war anwesend und der Pilot. Flog Dreamliner bis zur Rente.
Ich der Besitzer schaue zu.
Trimmung alles war super, aber irgendwas mit dem Expo stimmte nicht.
Selbst bei 100 passierte nicht viel, so wie die Beiden erwartet hätten.
Langsamer Anstieg der Klappen mit irgendwann schnellerer Bewegung.
Hab da mal das Setup abgehangen.
Muss da noch ein Parameter angepasst werden das das Expo zum Tragen kommt.
Mein Flieger ist die Produktionsnummer 38.
Die wollen nun alle das ich meine Futaba Funke nehme, will ich aber nicht.
Nicht weil die schlecht ist, sonder ich will zeigen das es auch damit geht.
Alles Engländer, schwerer Stand.
Schaut mal bitte was da falsch ist.
Man kann sehen, wenn ich langsam Höhe oder was auch immer langsam verstelle, da keine :Beschleunigung" passiert.
Beim Heli sieht man es.
Sehe gerade mit dem Setup kann ich nicht dienen. Erst morgen vielleicht.
Gruesse aus dem sonnigem Thailand
Volker
RV
15 March 2025 18:0715.03.2025 18:07
There is no setup included here. Please attach it as a zip file along with the macro cells.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Da ist kein Setup bei hier. Bitte samt Makrozellen als zip anfügen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Volker Wahlen
16 March 2025 03:0116.03.2025 03:01
Here's the setup.
I checked again this morning.
My stick movements are exactly the same as the servo.
I didn't create any macros.
Greetings from sunny Thailand
Volker file attachments:
Open |
Download - 11006398_vplane_Ediction.zip (625 bytes)
Hier das Setup.
Habe heute morgen nochmal geschaut.
Meine Stickbewegungen laufen exact gleich mit dem Servo.
Habe keine Makros gemacht.
Gruesse aus dem sonnigem Thailand
Volker
Dateianhänge:
öffnen |
Download -
11006398_vplane_Ediction.zip
(625 bytes)
Volker Wahlen
18 March 2025 13:1418.03.2025 13:14
I tried a new setup. No change.
Greetings from sunny Thailand
Volker
Hatte mal ein neues Setup gemacht. Keine Aenderung.
Gruesse aus dem sonnigem Thailand
Volker
Eddi E. aus G.
18 March 2025 14:1018.03.2025 14:10
Hi,
I just used a VPlane-NEO that was lying around here, connected a servo to CH2 (aileron) and powered it, held the aileron stick at about halfway, and pushed the expo measuring tape up and down... it rolls nicely.
The servo is chugging along merrily, so something seems to be changing.
Then I loaded your setup, same thing, same thing.
But different countries, different customs :-) As far as I know, Futaba uses a more progressive approach to the expo curve than we do, so that at high values you might get closer to a flat straight line with winglets (e.g. 100...30..15...0...15...30...100, flat between +/- 2/3 deflection, then relatively suddenly full).
One could of course go ahead and use the calculations CH2 and CH3 as inputs for curve macro cells at the servo connections CH2 and CH3, but this would be a bit more complex in terms of programming, but would allow more freedom.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
Ich habe eben mal eine VPlane-NEO, die hier noch so rum liegt, mit einem Servo an CH2 (Quer) und Strom versorgt, den Quer-Knüppel bei etwa Hälfte gehalten, und das Expo-Maßband rauf und runter 'geschubst' ... rollt ja schön nach.
Das Servo tuckert munter mit, scheint sich also was zu verändern.
Dann habe ich Dein Setup geladen, selbes, selbes.
Aber andere Länder, andere Sitten :-) Futaba geht m. W. bei der Expo-Kurve progressiver vor als wir, so dass man bei hohen Werten möglicherweise eher an eine flache Gerade mit Winglets ran kommt (bspw. 100...30..15...0...15...30...100, flach zwischen +/– 2/3 Ausschlag, dann relativ schlagartig voll).
Man könnte jetzt natürlich noch hergehen und die Berechnungen CH2 und CH3 jeweils als Eingänge für Kurven-Makrozellen an den Servo-Anschlüssen CH2 und CH3 nehmen, wird halt etwas aufwändiger in der Programmierung, würde aber mehr Freiheit erlauben.
Grüßle
Eddi
Born to fly ...
forced to work.
Eddi E. aus G.
18 March 2025 14:1318.03.2025 14:13
OT @Rainer: Just saw this. Registered: 18 years ago. We're of age!! :-) /OT
Born to fly ...
forced to work.
OT @Rainer: grad gesehen Registered: 18 years ago wir sind volljährig!! :-) /OT
Born to fly ...
forced to work.
Volker Wahlen
18 March 2025 16:0118.03.2025 16:01
Yes, that's how it is. This Expo thing isn't scientific with fixed rules?
It's somehow different with the helicopter, you can tell.
What can I do to become more sensitive to zero?
I think the 18-year-old thing is insider stuff :-)
Even at 100, not much really happens.
Greetings from sunny Thailand
Volker
Ja so sieht es aus. Diese Expo Geschichte ist nichts wissenschaftliches mit festen Regeln?
Beim Heli geht es irgendwie da merkt man es.
Was kann ich tun um feinfühliger um 0 zu werden?
Denke mal mit den 18 Jahren ist Insider Stuff :-)
Selbst auf 100 passiert nicht wirklich viel.
Gruesse aus dem sonnigem Thailand
Volker
Eddi E. aus G.
19 March 2025 08:5619.03.2025 08:56
Hi Volker,
No, there are no fixed rules for how to calculate the curve.
It was noted some time ago that this is different at other channels, and why not with us like with brands x, y, z... because it's not the same with them as it is with us ^^
As I said, curves: for example, a curve cell on CH2, input CH2 (what would normally be output there anyway), and then bend the curve accordingly. Same for CH3 (that would be the two ailerons, for elevator analogously on CH1, for rudder on tail, in each case where the servos are connected).
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Volker,
nee, feste Regeln gibt es nicht, wie die Kurve zu berechnen ist.
Vor längerer Zeit wurde schon mal bemerkt, dass das bei anderen Sendern anders ist, und warum bei uns nicht so wie bei Marke x, y, z ... weil's bei denen auch nicht so ist wie bei uns ^^
Wie gesagt, Kurven: bspw. auf CH2 eine Kurven-Zelle, Eingang CH2 (das was normal sowieso dort ausgegeben würde), und dann die Kurve entsprechend hinbiegen. Selbes für CH3 (das wären die beiden Querruder, für Höhe sinngemäß auf CH1, für Seite Tail, jeweils dort, wo die Servos angeschlossen sind).
Grüßle
Eddi
Born to fly ...
forced to work.
Volker Wahlen
19 March 2025 14:2619.03.2025 14:26
I'll make a video tomorrow with 0 expo and with 100.
That can't be it
Greetings from sunny Thailand
Volker
Ich mach mal morgen ein Video mit 0 Expo und mit 100.
Das kann es nicht sein
Gruesse aus dem sonnigem Thailand
Volker
Eddi E. aus G.
19 March 2025 15:0119.03.2025 15:01
Hi Volker,
Then please do as I wrote: hold the stick at about half, move the expo up and down, and see what the servo does.
But the solution with the cells – hand on heart – is also quick to dab on, possibly faster than making a video and writing back and forth ;-)
—Eddi
Born to fly ...
forced to work.
Hi Volker,
mach dann bitte so wie ich geschrieben habe: Knüppel auf etwa halb halten, Expo rauf und runter fahren, schau was das Servo macht.
Aber die Lösung mit den Zellen ist – Hand auf's Herz – auch schnell reingetupft, ggfs. schneller als ein Video machen und hin- und her schreiben ;-)
—Eddi
Born to fly ...
forced to work.
Volker Wahlen
20 March 2025 01:3420.03.2025 01:34
Okay, I'll see what happens and try my hand at the macros.
Greetings from sunny Thailand
Volker
Ok, ich schau mal was passiert und versuche mich auch mal an den Makros.
Gruesse aus dem sonnigem Thailand
Volker
Volker Wahlen
21 March 2025 04:3621.03.2025 04:36
Yes, the test shows that it's correct. It works.
With the macros I can also adjust more settings to make my Futaba English receivers happy.
Greetings from sunny Thailand
Volker
Ja, der Test zeigt da es richtig ist. Es geht.
Mit den Makros kann ich dann auch mehr einstellen das meine Futaba Engländer Glücklich sind.
Gruesse aus dem sonnigem Thailand
Volker
Eddi E. aus G.
21 March 2025 09:3021.03.2025 09:30
:-) :-)
Born to fly ...
forced to work.
:-) :-)
Born to fly ...
forced to work.