← VPlane / VBasic VLink

Surface programming translated

VBar › VPlane / VBasic VLink · Started by k.h.o.heli on 30 August 2025 20:0530.08.2025 20:05
k.h.o.heli 30 August 2025 20:0530.08.2025 20:05
Hello Mikado team,
I need your support; I'm programming a surface model for the first time.
Model type: Hotliner
Features:
CH1 - HR
CH2 - QR links
CH3 - QR right
I assigned the throttle function to the pitch stick: Cell type - Curve / Input - MC10/ESC
1. Special function: QR should act as a brake via switch 3 (option 3), HR mixed in.
2. Special function: When motor switch 5 is in the OFF position (Pos.A), the throttle function should be deactivated (for safety).
Sender: VBCT evo
Software: VPlane

I've already spent several hours on this, read information and watched videos, but I couldn't find a solution.

Thank you for your help

Regards, Kurt
machine-translated from German · Show original
Dirtygeri 31 August 2025 10:0231.08.2025 10:02
Hello Kurt!

2. Special function - you don't need to program anything, it's already set up that way... Engine switch in OFF - "throttle" is OFF, regardless of the throttle stick position... If you're that worried, there's also the safety switch... As Rainer always says, belt and suspenders... :-)

1. Special function - this is like if you want to mix in the ailerons as flaps, only in the opposite direction (up instead of down), there are also great videos by Rainer about this...

Look... you'll find what you're looking for :-)

Best regards, Geri
machine-translated from German · Show original
rutra 31 August 2025 10:2131.08.2025 10:21
Take a look here..... https://uroehr.de/vtube/page/6
machine-translated from German · Show original
k.h.o.heli 31 August 2025 18:4831.08.2025 18:48
Hello Geri,
I also thought that when the motor switch 5 is in the OFF position, the throttle stick is deactivated, but that is not the case.
Regardless of the position of the engine switch 5, the throttle is always active; I have also checked the safety switch 4.
It is activated (OFF) and yet the engine still runs ON.
machine-translated from German · Show original
Fingolf 31 August 2025 19:5631.08.2025 19:56
Gas should be on ESC and not manually on a macro cell.
Change that, sb.

Stephan
machine-translated from German · Show original
Dirtygeri 1 September 2025 10:4301.09.2025 10:43
Hello Kurt!

Please connect the channels as intended -> ESC = Motor, Tail = Rudder, CH1 = Elevator, CH2 and CH3 = Ailerons, if I'm not mistaken...
I found an old, homemade guide for the additive that might help you...

LG Geri File attachments:
Open | Download - VBAR-Ailerons-as-Flaps.zip (350.6 KB)
machine-translated from German · Show original
k.h.o.heli 2 September 2025 01:4402.09.2025 01:44
Hello Geri,
I followed your instructions, and after a few tries it worked.
First, I removed the gas function from the macrocell, as Stephan advised.
The engine off function and the safety function are now correctly set.
Programming a surface model with the Mikado system is a
A real challenge; I couldn't have done it alone. Thank you so much for your help.
Many thanks to everyone else for the quick support.

Regards, Kurt
machine-translated from German · Show original
Eddi E. aus G. 2 September 2025 09:0602.09.2025 09:06
Hi Kurt,

Well, I think it's (perhaps too...) easy :-)

Model setup
. configure everything there, for the respective connections, control surface type, mixing ratios, drive
. go flying

It has everything you need for a 4-flap model with a motor; I don't even need to know the word "macrocell"...
Motor switches and safety switches are always active on the connection for the drive, regardless of whether it's a helicopter, fixed-wing aircraft, or something else.

You wouldn't start any transmitter by programming a model from scratch with free mixers...

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
k.h.o.heli 17 September 2025 20:1917.09.2025 20:19
Hi Eddi,

I still need help!
Initial situation:
Sender: VBCT evo
Software: VPlane
Electric gliders: 2QR / 1HR

I have made the following settings:

Surface Mixer Setup
Flap type: Transverse
Output slot CH2
Output min / max -35 / 50
Cross Mix 100
Flap Mix 50

Flap type: Transverse
Output slot CH3
Output min / max -50 / 35
Cross Mix 100
Flap Mix 50

Macrocells:

MC09 / Flap
Cell type: Channel
Input Signal: MC11 / E1CH1
Limit min / max: -120 / 120
Distance min / max: -120 / 120
Rate of change: 3

MC11 / E1CH1
Cell type: 3-level
Entrance: Sw Op 3
Exit down: 0
Starting average: 60
Output up: 120

With these settings (function and rudder deflection), the setup is OK.
Now my problem: I use the QR code as a brake, when activating it
Switch 3 (Sw Op 3) moves the QR upwards and the HR slightly
downwards. However, the aileron deflection is too small for me when I use the flap mix.
Changing the value to 50 does nothing.
How do I solve this problem?

Many thanks for your support

Regards, Kurt
machine-translated from German · Show original
Eddi E. aus G. 18 September 2025 09:5918.09.2025 09:59
Good morning,

What does the MC11 have to do with this...?

Which model setup did you use as a basis?

Even if there are only 2 QR codes, if I want to use the flap function on them, I would use the standard + flaps as a basis. Then I can use the flap function MC09 and MC27 (long click on CH2) in the setup, for example, and don't have to reprogram anything manually – even if no flaps are physically installed or connected.

Just tried it, it works, it has both the QR deflection and the programmed flap deflection.

No MC11...

Grüßle

Eddi

Born to fly ...
forced to work.



2 mal bearbeitet. Zuletzt am 18.09.2025 11:14 von Eddi E. aus G..
machine-translated from German · Show original
k.h.o.heli 18 September 2025 11:0218.09.2025 11:02
Hi Eddi,

Thanks for the quick information, I'll look into it this weekend.

Regards, Kurt
machine-translated from German · Show original
k.h.o.heli 24 September 2025 11:4724.09.2025 11:47
Hello everyone,

I still haven't managed to program my model.
The more I adjust, the less it fits. First, make a few.
Take a few days off. I'll be in touch again.

Regards, Kurt
machine-translated from German · Show original
Eddi E. aus G. 24 September 2025 13:2924.09.2025 13:29
Good morning,

When you have the mental space again: where is the problem?

Height, side, lateral, drive already?
Or only at the flaps?

Of course, if you've messed things up and want to start over, the following is important:
Delete macro cells
New setup

If necessary, we can also do supervised hiring over the phone; we would just need to arrange something.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
k.h.o.heli 29 September 2025 19:3929.09.2025 19:39
Hi Eddi,

Thank you for the offer and for your patience.

Here's another attempt.

Basis: Model setup - Standard + Flaps

Surface Mixer Setup

Valve type: Flaperon
Output slot CH2
Output min / max -38 / 42
Cross Mix 100
Flap Mix 120

Valve type: Flaperon
Output slot CH3
Output min / max -42 / 38
Cross Mix 100
Flap Mix 120

MC09 / Flap
Cell type: Channel
Input Signal: MC27
Limit min / max: -120 / 120
Distance min / max: -120 / 120
Rate of change: 3

MC27
Cell type: 3-level
Entrance: Sw Op 3
Exit down: 0
Starting average: 60
Output up: 120

With these settings, QR and HR readings are correct.
The problem: I use the QR code as a brake; when activating it...
The QR does not move far enough upwards when switch 3 (SW OP 3) is activated.
How can I make the rash bigger?

Many thanks for your support

Regards, Kurt
machine-translated from German · Show original
Eddi E. aus G. 30 September 2025 09:2030.09.2025 09:20
Good morning,

Looking at the aileron min/max settings, I think you need to adjust them so that you achieve the desired deflection (min/middle/max) with the flap function (without ailerons, mix initially set to 0), possibly also adjusting mechanically (servo arm center, perhaps even one hole further out, or one hole further in on the rudder, whichever is easier or even possible).
Then adjust the cross-mixer (only) as high as you need it (around 40% if you could transfer it to the current min/max values), but also make sure that nothing mechanically engages, balance if necessary.

At the moment, you need to limit the aileron servo travel so that not much is left for the flaps (in layman's terms, 120% of 40% would be 48%; depending on where the center is, the total travel may be shifted a little further, but not by much).

The approach (thought about it the other way around) is then a flap with aileron mixing, but the result (movement) is the same.

Ah, helicopters are so simple ^^

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
k.h.o.heli 1 October 2025 10:2001.10.2025 10:20
Hi Eddi,

You're right, helicopters are so simple. I've built three helicopters with the Mikado system in the last two years.
It was programmed and configured, and there were absolutely no problems; I was and still am thrilled.
I will be making mechanical modifications to my electric glider.

Thanks again for your support!

Regards, Kurt
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless