← VPlane / VBasic VLink

Activate Vplane translated

VBar › VPlane / VBasic VLink · Started by Epro500 on 8 April 2026 21:4408.04.2026 21:44
Epro500 8 April 2026 21:4408.04.2026 21:44
Hello,

I bought and installed a new Vstabi Evo with pro+rescue update (V8.2).
So far, everything has worked out.
So far I've only operated helicopters. Now I want to program a glider with two ailerons, elevator, rudder, and motor.

When I turn on the VBC Touch and connect it to the vstabi, I only see the helicopter programs.
I downloaded VPlane Neo/Evo Basic from the shop.
How do I activate the app?

LG
Erich
machine-translated from German · Show original
RV 8 April 2026 23:0108.04.2026 23:01
Hello Erich,

The VPlane firmware needs to be installed on the stabilizer. Connect the stabilizer, open the VBar Updater in VBCt, click Update to check, scan the QR code (log in and scan again if necessary), select Plane in the store, update again... and there it is ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 08.04.2026 23:01 von RV.
machine-translated from German · Show original
Epro500 9 April 2026 08:1709.04.2026 08:17
Hello Rainer,

Thanks for the quick reply. It worked now after reconnecting to the Vbar Control Manager.

Now I need to look into the macrocells in order to use the two ailerons as controlled flaps.

LG
Erich
machine-translated from German · Show original
Eddi E. aus G. 9 April 2026 08:5709.04.2026 08:57
Hi Erich,

uh... no ;-)

Set up the model via the setup menu, using one with flaps as a template.
You can also adjust the flaps via the setup (even if no servos are connected).
You can adjust the flap mixing by long-clicking on the aileron servos.
_or_
Connect the QR servos to the flap connectors, initially configure them as flaps, and then set an aileron mix via long click.

Voilà, no macrocell needed – well, actually, because the flap function uses macrocells, but it's directly and easily accessible via the setup.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Epro500 9 April 2026 11:1109.04.2026 11:11
Hello Rainer,

Great, so everything's set up. I kind of figured as much. ????
Then I'll try that tonight…

Thanks and best regards
Erich
machine-translated from German · Show original
Epro500 9 April 2026 19:3009.04.2026 19:30
Hello Rainer,

So I couldn't get the controllable airbrakes to work via the setup alone...? ????
I would need more detailed information on what needs to be done.

I then tried it using your VP Lane setup guide (1st post) and it works now! ???? (with macro cells 9 and 11 as you described…)

LG
Erich
machine-translated from German · Show original
Eddi E. aus G. 10 April 2026 09:0410.04.2026 09:04
Hi Erich,

If it works, then everything's fine.

During setup, depending on the selected model type, functions are pre-assigned; if flaps are selected, then flaps are also assigned, and thus also macro cells 9 and 27.

Normally, you would connect all servos according to the display in the setup, QR to CH2 and 3, LK to CH4 and AUX3, adjust them, and you're done.

If you wanted to mix the functions, you could use a long click to set the mixing ratios, e.g. flaps to elevator (with the elevator servo), aileron to rudder (with the rudder servo), or aileron to flaps (with the aileron servos) or flaps to aileron (with the aileron servos).

With this, the surface mixer aka setup can actually map pretty much all non-exotic functions, and especially with stabilization, but also with all the other 'magic' included, including agility, sensitivity, expo, trims/autotrim.

When mixing manually, 'pay attention' :-) ... the pure functions, e.g., tail, are just the sticks directly; the functions with FC-[...] in the name (FC = Flight Control) are the processed functions.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Epro500 10 April 2026 14:0610.04.2026 14:06
Hello Rainer,

Mechanically it works, but I just noticed that there's no stabilization/control?? (so when I move the VBar, nothing happens)

What could be the reason for this?

LG
Erich
machine-translated from German · Show original
Epro500 10 April 2026 21:4510.04.2026 21:45
Hi Eddi,

I found the problem: the sensitivities were set to 0…

By the way, I tried it again via setup as you described (with the aileron servos connected to the flap outputs) and it all worked! ????

Thank you for your support!
LG
machine-translated from German · Show original
Epro500 10 April 2026 21:5310.04.2026 21:53
…the four question marks were actually supposed to be a smiley face.
machine-translated from German · Show original
Eddi E. aus G. 13 April 2026 09:1313.04.2026 09:13
Hi Erich,

:-) Look :-) Life can be so simple!

Sensitivity 0 is the default in Bank 1, meaning it's unstabilized.

This can be helpful if you want to 'feel' the model, or if you've made a serious mistake during setup (e.g., defining the sensor mounting position incorrectly in the setup... it's happened before, but luckily nothing serious occurred because the VBar remains manageable due to its programming; it was just a bit nerve-wracking for the pilot in the circuit with a large jet...). If only he'd remembered Bank 1... ;-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless