← VPlane / VBasic VLink

Vplane limits translated

VBar › VPlane / VBasic VLink · Started by Epro500 on 25 August 2026 15:0325.08.2026 15:03
Epro500 25 August 2026 15:0325.08.2026 15:03
Hello,

I have a question about the limits:
When I program an e-glider via the setup menu, I set limits for the ailerons, for example, up and down. For instance, +/- 10 mm. If I then program a butterfly mixer, do I need an additional 10 mm of upward deflection and would I have to increase the aileron limit by 10 mm? Or is there another way?

Question 2: Is it generally possible to activate a mixer from multiple or two different switches?

LG
Erich
machine-translated from German · Show original
Eddi E. aus G. 25 August 2026 16:2925.08.2026 16:29
Hi Erich,

Correct. Output min/max specifies the maximum allowed value.
The maneuverability then determines the difference per bank (almost practically in percent).
The stabilization adds a little extra, as it works around the position of the control surface.
Mix proportions accordingly, up to min/max. That's it.
Just try figuring it out, you can see it directly on the model.

Regarding the second question, please describe in more detail what you are planning, and... why :-) ?

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Epro500 24 September 2026 18:5024.09.2026 18:50
Hi Eddi,

Sorry for the late reply.

Over the last few weeks I've flown a lot with the e-glider (F5K and 2.1m DjangoS) and worked out various values.
Considering I come from helicopters and am a beginner in gliding, the gliders with VBar fly incredibly well :-) the little F5K flies like it's on rails even at higher speeds :-) space-wise it's challenging, but worth every effort.
I think the usual different limitations on the upward/downward deflections are no longer so important in principle with VPlane.

For the macros, I was thinking more along the lines of the butterfly position on the throttle stick (adjustable) with the engine off.
You do have general instructions, but to be honest, I don't understand enough about the exact implementation…
Is there perhaps a tutorial with screenshots for this? :-) I would be very grateful if I wanted to implement it.

LG
Erich
machine-translated from German · Show original
Eddi E. aus G. 25 September 2026 09:3625.09.2026 09:36
Hi Erich,

I'm already looking forward to it!

Regarding BF, I could just look at Rainer's explanations in Start-Stop-Start and try to replicate them, but I don't have anything ready to show it more clearly than with servos on the table.

I am quite sure (even as a complete non-computer user) that it works just as well with the Touch/EVO, the logic and menus are the same as with the Classic, and you can even name the cells, which greatly simplifies finding them later.

Simply put, without any unnecessary details: the outputs for the respective control surfaces are multiplexed. When the engine is idling and running, these multiplexers have the original function as their input (e.g., CH2 to CH2, CH3 to CH3, etc.). When the engine is off, a mixer is used between the original function and a cam module, which in turn has the throttle stick as its input. The cam module then allows you to adjust the direction of rotation and the mixing ratio to match the stick position.
For control surfaces that have the same signs, you can possibly use the same strand as the input; for those that don't, you would have to crochet one separately for each.
If desired, the switching between throttle and foot-first could also be controlled by a trigger cell that differentiates between throttle (0-100) and foot-first (0-100) from the switching point (trigger greater than or equal to one does this, less than or equal to another) at the stick's midpoint. This would again require multiplexers (the trigger being the input) and curves (direction/mixing ratio/stick position).

Simply save your current state (setup and macro cells) so you can always return to it, and then grab a control surface to practice with... have fun and good luck!

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Epro500 4 October 2026 19:2404.10.2026 19:24
Thanks for your support, Eddi!
I haven't needed flaps so far anyway. I'll set up some servos for testing over the winter…

LG
Erich
machine-translated from German · Show original
Eddi E. aus G. 5 October 2026 10:4205.10.2026 10:42
Good morning,

gladly!

I would try it directly on the model, that way you can clearly see what happens. Remove the propeller, or use a servo as a pointer instead of the speed controller.
As I said, save the setup and macrocell setup beforehand so that you can always go back to it.

Gutes Gelingen!

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless