English below.
Hello,
Has anyone ever implemented a governor-controlled idle speed with a VPlane on a gasoline engine?
My setup:
- VBar NEO with VPlane
- VControl Touch EVO+
- Petrol engine with normal throttle servo
- RCEXL ignition with RPM/speedometer output
- The RPM signal is routed to the RPM input of the NEO via an optocoupler.
What I want to achieve is active control of the idle speed via the RPM signal. This means: A desired idle speed is specified, and VBar automatically adjusts the throttle servo position in small increments to maintain this speed at idle.
I'm familiar with the normal idle function in VPlane, which essentially sets a fixed throttle position or idle trim. That's not the function I'm referring to.
At the same time, the VBar system includes Nitro/Expert Governor functions that can control a throttle servo via RPM feedback.
Has anyone actually implemented a closed-loop RPM control for idle using VPlane?
I would be particularly interested in:
- Can the Nitro/Expert Governor be used with V-Plane in any way?
- Can the NEO's RPM input be used as feedback for controlling the throttle servo?
Is there another function or workaround in VPlane that can achieve the same result?
Experiences from someone who has actually tried this or successfully implemented it would be particularly interesting. Screenshots of the settings would also be very helpful.
Thank you!
English
Title: VPlane – governor-controlled idle RPM on a gasoline engine?
Hi,
Has anyone successfully implemented governor-controlled idle RPM in VPlane on a gasoline engine?
My setup:
- VBar NEO with VPlane
- VControl Touch EVO+
- Gasoline engine with a standard throttle servo
- RCEXL ignition with RPM/tacho output
- The RPM signal is fed through an opto-isolator to the RPM input on the NEO
What I would like to achieve is active closed-loop control of the engine idle using RPM feedback. In other words, a desired idle RPM is set, and VBar makes small automatic corrections to the throttle servo position to maintain that RPM at idle.
I am familiar with the normal VPlane idle function, where essentially a fixed throttle position/idle trim is set. That is not the function I am looking for.
At the same time, the VBar system has Nitro/Expert Governor functions that can use RPM feedback to control a throttle servo.
Has anyone actually implemented closed-loop RPM control of engine idle with VPlane?
I am particularly interested in:
- Can the Nitro/Expert Governor somehow be used together with VPlane?
- Can the NEO RPM input be used as feedback to control the throttle servo?
- Is there another VPlane function or workaround that achieves the same result?
I would particularly appreciate feedback from anyone who has actually tested or successfully implemented this. Screenshots of the relevant settings would also be very helpful.
Thanks!
Edited once. Last edited on 04/10/2026 at 13:54 by bjorn.are@pm.me .
Hello,
Has anyone ever implemented a governor-controlled idle speed with a VPlane on a gasoline engine?
My setup:
- VBar NEO with VPlane
- VControl Touch EVO+
- Petrol engine with normal throttle servo
- RCEXL ignition with RPM/speedometer output
- The RPM signal is routed to the RPM input of the NEO via an optocoupler.
What I want to achieve is active control of the idle speed via the RPM signal. This means: A desired idle speed is specified, and VBar automatically adjusts the throttle servo position in small increments to maintain this speed at idle.
I'm familiar with the normal idle function in VPlane, which essentially sets a fixed throttle position or idle trim. That's not the function I'm referring to.
At the same time, the VBar system includes Nitro/Expert Governor functions that can control a throttle servo via RPM feedback.
Has anyone actually implemented a closed-loop RPM control for idle using VPlane?
I would be particularly interested in:
- Can the Nitro/Expert Governor be used with V-Plane in any way?
- Can the NEO's RPM input be used as feedback for controlling the throttle servo?
Is there another function or workaround in VPlane that can achieve the same result?
Experiences from someone who has actually tried this or successfully implemented it would be particularly interesting. Screenshots of the settings would also be very helpful.
Thank you!
English
Title: VPlane – governor-controlled idle RPM on a gasoline engine?
Hi,
Has anyone successfully implemented governor-controlled idle RPM in VPlane on a gasoline engine?
My setup:
- VBar NEO with VPlane
- VControl Touch EVO+
- Gasoline engine with a standard throttle servo
- RCEXL ignition with RPM/tacho output
- The RPM signal is fed through an opto-isolator to the RPM input on the NEO
What I would like to achieve is active closed-loop control of the engine idle using RPM feedback. In other words, a desired idle RPM is set, and VBar makes small automatic corrections to the throttle servo position to maintain that RPM at idle.
I am familiar with the normal VPlane idle function, where essentially a fixed throttle position/idle trim is set. That is not the function I am looking for.
At the same time, the VBar system has Nitro/Expert Governor functions that can use RPM feedback to control a throttle servo.
Has anyone actually implemented closed-loop RPM control of engine idle with VPlane?
I am particularly interested in:
- Can the Nitro/Expert Governor somehow be used together with VPlane?
- Can the NEO RPM input be used as feedback to control the throttle servo?
- Is there another VPlane function or workaround that achieves the same result?
I would particularly appreciate feedback from anyone who has actually tested or successfully implemented this. Screenshots of the relevant settings would also be very helpful.
Thanks!
Edited once. Last edited on 04/10/2026 at 13:54 by bjorn.are@pm.me .
English below.
Hallo,
hat jemand schon einmal eine Governor-geregelte Leerlaufdrehzahl mit VPlane bei einem Benzinmotor realisiert?
Mein Setup:
- VBar NEO mit VPlane
- VControl Touch EVO+
- Benzinmotor mit normalem Gasservo
- RCEXL-Zündung mit RPM/Tacho-Ausgang
- Das RPM-Signal wird über einen Optokoppler an den RPM-Eingang des NEO geführt
Was ich erreichen möchte, ist eine aktive Regelung der Leerlaufdrehzahl über das RPM-Signal. Das heißt: Eine gewünschte Leerlaufdrehzahl wird vorgegeben und VBar korrigiert die Stellung des Gasservos automatisch in kleinen Schritten, um diese Drehzahl im Leerlauf konstant zu halten.
Die normale Idle-Funktion in VPlane, bei der im Prinzip eine feste Gasposition bzw. ein Idle-Trim eingestellt wird, kenne ich. Diese Funktion meine ich nicht.
Gleichzeitig gibt es im VBar-System Nitro/Expert-Governor-Funktionen, die über RPM-Feedback ein Gasservo regeln können.
Hat jemand tatsächlich schon eine Closed-Loop-RPM-Regelung für den Leerlauf mit VPlane umgesetzt?
Mich würde insbesondere interessieren:
- Kann der Nitro/Expert Governor irgendwie zusammen mit VPlane verwendet werden?
- Kann der RPM-Eingang des NEO als Feedback zur Regelung des Gasservos verwendet werden?
- Gibt es eine andere Funktion oder einen Workaround in VPlane, mit dem sich dasselbe erreichen lässt?
Besonders interessant wären Erfahrungen von jemandem, der dies tatsächlich ausprobiert oder erfolgreich umgesetzt hat. Screenshots der Einstellungen wären natürlich ebenfalls sehr hilfreich.
Vielen Dank!
English
Title: VPlane – governor-controlled idle RPM on a gasoline engine?
Hi,
Has anyone successfully implemented governor-controlled idle RPM in VPlane on a gasoline engine?
My setup:
- VBar NEO with VPlane
- VControl Touch EVO+
- Gasoline engine with a standard throttle servo
- RCEXL ignition with RPM/tacho output
- The RPM signal is fed through an opto-isolator to the RPM input on the NEO
What I would like to achieve is active closed-loop control of the engine idle using RPM feedback. In other words, a desired idle RPM is set, and VBar makes small automatic corrections to the throttle servo position to maintain that RPM at idle.
I am familiar with the normal VPlane idle function, where essentially a fixed throttle position/idle trim is set. That is not the function I am looking for.
At the same time, the VBar system has Nitro/Expert Governor functions that can use RPM feedback to control a throttle servo.
Has anyone actually implemented closed-loop RPM control of engine idle with VPlane?
I am particularly interested in:
- Can the Nitro/Expert Governor somehow be used together with VPlane?
- Can the NEO RPM input be used as feedback to control the throttle servo?
- Is there another VPlane function or workaround that achieves the same result?
I would particularly appreciate feedback from anyone who has actually tested or successfully implemented this. Screenshots of the relevant settings would also be very helpful.
Thanks!
1 mal bearbeitet. Zuletzt am 04.10.2026 13:54 von bjorn.are@pm.me.
Hallo,
hat jemand schon einmal eine Governor-geregelte Leerlaufdrehzahl mit VPlane bei einem Benzinmotor realisiert?
Mein Setup:
- VBar NEO mit VPlane
- VControl Touch EVO+
- Benzinmotor mit normalem Gasservo
- RCEXL-Zündung mit RPM/Tacho-Ausgang
- Das RPM-Signal wird über einen Optokoppler an den RPM-Eingang des NEO geführt
Was ich erreichen möchte, ist eine aktive Regelung der Leerlaufdrehzahl über das RPM-Signal. Das heißt: Eine gewünschte Leerlaufdrehzahl wird vorgegeben und VBar korrigiert die Stellung des Gasservos automatisch in kleinen Schritten, um diese Drehzahl im Leerlauf konstant zu halten.
Die normale Idle-Funktion in VPlane, bei der im Prinzip eine feste Gasposition bzw. ein Idle-Trim eingestellt wird, kenne ich. Diese Funktion meine ich nicht.
Gleichzeitig gibt es im VBar-System Nitro/Expert-Governor-Funktionen, die über RPM-Feedback ein Gasservo regeln können.
Hat jemand tatsächlich schon eine Closed-Loop-RPM-Regelung für den Leerlauf mit VPlane umgesetzt?
Mich würde insbesondere interessieren:
- Kann der Nitro/Expert Governor irgendwie zusammen mit VPlane verwendet werden?
- Kann der RPM-Eingang des NEO als Feedback zur Regelung des Gasservos verwendet werden?
- Gibt es eine andere Funktion oder einen Workaround in VPlane, mit dem sich dasselbe erreichen lässt?
Besonders interessant wären Erfahrungen von jemandem, der dies tatsächlich ausprobiert oder erfolgreich umgesetzt hat. Screenshots der Einstellungen wären natürlich ebenfalls sehr hilfreich.
Vielen Dank!
English
Title: VPlane – governor-controlled idle RPM on a gasoline engine?
Hi,
Has anyone successfully implemented governor-controlled idle RPM in VPlane on a gasoline engine?
My setup:
- VBar NEO with VPlane
- VControl Touch EVO+
- Gasoline engine with a standard throttle servo
- RCEXL ignition with RPM/tacho output
- The RPM signal is fed through an opto-isolator to the RPM input on the NEO
What I would like to achieve is active closed-loop control of the engine idle using RPM feedback. In other words, a desired idle RPM is set, and VBar makes small automatic corrections to the throttle servo position to maintain that RPM at idle.
I am familiar with the normal VPlane idle function, where essentially a fixed throttle position/idle trim is set. That is not the function I am looking for.
At the same time, the VBar system has Nitro/Expert Governor functions that can use RPM feedback to control a throttle servo.
Has anyone actually implemented closed-loop RPM control of engine idle with VPlane?
I am particularly interested in:
- Can the Nitro/Expert Governor somehow be used together with VPlane?
- Can the NEO RPM input be used as feedback to control the throttle servo?
- Is there another VPlane function or workaround that achieves the same result?
I would particularly appreciate feedback from anyone who has actually tested or successfully implemented this. Screenshots of the relevant settings would also be very helpful.
Thanks!
1 mal bearbeitet. Zuletzt am 04.10.2026 13:54 von bjorn.are@pm.me.
machine-translated from German · Show original