I’m trying to set up a N7 gasser convertion with Neo and Vcontrol and everything is moving in the right direction but the tail is compensating the wrong way. The tail is moving the right way from the TX commands so the servo doesn’t need to be reverse. The Neo is set to the right mounting configuration and main rotor is set to CW rotation. Any help would be greatly appreciated
Help with tail compensating in the wrong direction
VBar › VBar NEO/EVO VLink ·
Started by joecass on 25 November 2019 04:1725.11.2019 04:17
joecass
25 November 2019 04:1725.11.2019 04:17
Vinger
25 November 2019 06:0325.11.2019 06:03
As on Helifreak post, tail blades are mounted incorrectly for a CCW rotating tail.
VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
RV
25 November 2019 06:3125.11.2019 06:31
This is impossible - even with wrong mounted tail grips or blades when you obtain the rotationg/thrust direction as the air does too and not other "helpers".
Please post a few pictures of this heli, its rotors incl. swasplate, main grips, full tail, rotation direction and the setup.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Please post a few pictures of this heli, its rotors incl. swasplate, main grips, full tail, rotation direction and the setup.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
25 November 2019 10:3025.11.2019 10:30
On the N7 main blades turn CW and the tail turns CW. So the blades are not on wrong and the tail grips are on correctly.
Pictures were too big so I had to send it in the Helifreaks link scroll down to the bottom you will see the pictures.
https://www.helifreak.com/showthread.php?p=7926411#post7926411
How do I attach set up file when using vcontrol?
1 mal bearbeitet. Zuletzt am 25.11.2019 10:46 von joecass.
Pictures were too big so I had to send it in the Helifreaks link scroll down to the bottom you will see the pictures.
https://www.helifreak.com/showthread.php?p=7926411#post7926411
How do I attach set up file when using vcontrol?
1 mal bearbeitet. Zuletzt am 25.11.2019 10:46 von joecass.
RV
25 November 2019 15:5525.11.2019 15:55
Store to VBC (model connected), connect VBC to USB, navigate to the vbar folder ... zip and upload the setup file here.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
26 November 2019 04:5726.11.2019 04:57
I hope I did this right and this is the file you need
| -
Synergy_Gas.zip
(526 bytes)
RV
26 November 2019 19:3726.11.2019 19:37
I have loaded the setup here and all seems to be okay.
Just watch this way:
- Preconditionally - we have the stick mode on tail which means "Stick to right is clockwise pirouette (CW)" - we move the nodse as usual. (REASON: some guys steer the tail instead nose - they may fail here if they didn't select this in VBCt or swap/resolder the poti cables in VBC)
- Is VBC stick calibration Tail Stick to right side then giving positive % numbers?
- does the stick to the right side move tail blades as needed fpr clockwise pirouette which means on a CW rotating system the "against the torque" direction too?
- does the gyro work the same direction when moving the heli CCW?
- now zero integral and use maximum DMA at one bank for check on the bench
- starting from zero collective - and going up or down - do the tail blades move in the same direction as for CW pirouettes?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Just watch this way:
- Preconditionally - we have the stick mode on tail which means "Stick to right is clockwise pirouette (CW)" - we move the nodse as usual. (REASON: some guys steer the tail instead nose - they may fail here if they didn't select this in VBCt or swap/resolder the poti cables in VBC)
- Is VBC stick calibration Tail Stick to right side then giving positive % numbers?
- does the stick to the right side move tail blades as needed fpr clockwise pirouette which means on a CW rotating system the "against the torque" direction too?
- does the gyro work the same direction when moving the heli CCW?
- now zero integral and use maximum DMA at one bank for check on the bench
- starting from zero collective - and going up or down - do the tail blades move in the same direction as for CW pirouettes?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
27 November 2019 03:5527.11.2019 03:55
Ok thank you everting is moving the correct way.
RV
27 November 2019 06:1927.11.2019 06:19
Okay - well done - so all is ok and good for flying. Please don't forget to enter the old Integral and DMA values again ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.