← VBar NEO/EVO VLink

Vbar Mini with Sat and retractable landing gear setup

VBar › VBar NEO/EVO VLink · Started by Dwlads on 3 January 2020 13:1103.01.2020 13:11
Dwlads 3 January 2020 13:1103.01.2020 13:11
Hi,

After a deep web search and a wild hunt on Youtube, I am almost sure that the answer to my question is no. But I got to have faith and ask anyway:
Using a Mini Vbar with Rx-Satellite may I connect a retractable landing gear servo into Mini Vbar and set it on the Vbar Control?

Thank you
RV 3 January 2020 13:4803.01.2020 13:48
Yes - just use either the Expert Aux App (for Experts, could also access signal pins on AUX1 for 2 more servos)

https://www.vstabi.info/en/node/1797

Or the Pro Aux (more simple, would be enough for one servo with delay)

https://www.vstabi.info/en/node/1733

Btw ... we have moved all our videos from Youtube to our own VTube

https://www.vstabi.info/en/node/2282

https://uroehr.de/vtube/cat/english-videos

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Dwlads 3 January 2020 15:1303.01.2020 15:13
Thank you Rainer :-)

I really appreciated your help. I will follow the guidelines and share the progress here.

Best
Dwlads 3 January 2020 16:4403.01.2020 16:44
Disclaimer: the original message was edited to clarify the right way to wire the Vbar Mini. The original screenshot was replaced too with the correct wire diagram.

Rainer,

Just to clarify the wiring (I will use the Expert Aux App):



I will connect the signal from RXA/Rudder, and get the power from RXC ground and positive.

Best



1 mal bearbeitet. Zuletzt am 04.01.2020 03:17 von Dwlads.
Dwlads 3 January 2020 19:3103.01.2020 19:31
Oh...I think I got it!

Since I am using a Vbar Mini is mandatory to use the Expert Aux App.

The first table on page https://www.vstabi.info/en/node/1797 said Pro Aux App is not available on a Vbar Mini.

The same table shows Vbar Mini has only 2 outputs, RXA Center Pin in Cell 2 (elevator) and RXA lower Pin is Cell 1 (Rudder).

So, I will wire the signal on RXA lower Pin and have the power from ground and positive pins from RXC. After that will configure using Expert Aux App.

Best.
Dwlads 4 January 2020 02:5904.01.2020 02:59
It works like a charm!

After wired the Vbar Mini and config Expert Aux App everything runs as expected.
Below two screenshots with the parameters, I have set. Maybe the screenhshots could be useful for someone in the future:






Thank you again Rainer for your help.



1 mal bearbeitet. Zuletzt am 07.01.2020 02:34 von Dwlads.
RV 4 January 2020 09:1704.01.2020 09:17
:-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless