johnpssa
21 May 2026 20:2621.05.2026 20:26
Hello,
Vcontrol Touch - Vlink S.BUS micro RX - OMP M2 V3
The Touch is fully updated with MacroCells installed.
Enabled Sbus and telemetry in the OMP app.
Linked to RX setup new model and selected the S.Bus V3 option.
The model appears to be correctly setup the only issue is it appears I have only partial telemetry.
When you connect it ask to select a battery pack and when I disconnect it shows a screen with data that indicates telemetry.
However no RPM or mah count is available and you get a continuous battery voltage 0.0v warning.
Thanks
John Plumbley
RV
21 May 2026 23:1021.05.2026 23:10
Please check the update rate for the S.Bus in the VBar Macrocells settings. It must be set to 10ms.
If this is set right - I must say the problem must be addressed to OMP. In the cloud I can see incoming telemetry data - but zero. As all teleemtry data is securesd and encrypted we can exclude a tranmission issue on our side.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Please check the update rate for the S.Bus in the VBar Macrocells settings. It must be set to 10ms.
If this is set right - i must say the problem must be adressed to OMP. In the cloud i can see incoming telemetry data - but zero. As all teleemtry data is securesd and encrypted we can exclude a tranmission issue on our side.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
johnpssa
22 May 2026 09:4122.05.2026 09:41
Hi Rainer, thanks for the response.
Not sure if I should be looking for an actual macro cell, If I look in I/O Configuration
AUX1 =>S.BUS and Update AUX 1 output is set to 10 milliseconds
Not sure if there is a direct relationship but macro cell 6/AUX 1 is not active,
I did notice when I loaded the data to the RX the status bar gets to the end but then flicks complete/ not complete for about 20seconds before it appears to finish
Thanks
John Plumbley
Eddi E. aus G.
22 May 2026 10:1522.05.2026 10:15
Hi,
in I/O Config, AUX1 is linked to S.BUS out, which overrides the normal function.
The macrocell 06/AUX1 has no function assigned so the original function (none) is active, but that's also not relevant, because I/O Config overrides it anyway.
Is the OMP telemetry App installed on VBar Control, does it pop up?
If so, what does it show, when you click it (short tap, long tap, send screenshots, please)?
Best,
Eddi
Born to fly ...
forced to work.
johnpssa
22 May 2026 10:3822.05.2026 10:38
Hi Eddi,
Is the OMP telemetry app installed - NO!!!! Can’t believe I missed that.
Just installed the app and all is working, thanks for the idiots guide.
JohnPlumbley
Eddi E. aus G.
22 May 2026 10:4522.05.2026 10:45
:-)
Born to fly ...
forced to work.