Chriss
7 June 2026 22:0407.06.2026 22:04
Hello Rainer,
I noticed that you have a value of 119 for Cyclic in the setup.
Is it good for the regulation if the value is so high?
How did you arrive at such a high value? Did you mount your ball bearing on the servo arm more towards the inside?
I'm only getting one value for Cyclic Calibration ----- ----- 89 ----- -----.
Is this still good or rather rubbish?
With my Huhges 500, it's like this: when controlled cyclically with short inputs while hovering, it makes a slight wobbling/wobbling motion, and in cruising flight when it gets fast, it rears up.
Serial No. Neo.11004721
1340rpm at the head.
12S
7kg.
Benda 5-blade head, unsteamed.
Witte 630 sheets 144g Symmetrical
Maximum pitch: 15 degrees.
What do you think of the setup, Rainer?
Kind regards
Hallo Rainer,
Mir ist aufgefallen daß du im Setup für Zyklisch einen wert von 119 hast.
Ist das gut für die Regelung wenn der wert so hoch ist ?
Wie kommst du auf so einen hohen wert, hast du deine Kugel am Servoarm eher innen montiert ?
Ich komme bei mir nur auf einen wert von Zyklische Kalibrierung ----- ----- 89 ----- -----.
Ist das noch gut oder eher mist. ?
Bei meiner Huhges 500 ist es leiter so, wenn zyklisch mit kuzen input im Schweben gesteuert wird sie so ein leichtes nachwippen/nacheiern macht, und im Marschflug wenn sie schnell wird aufbäumt.
SerNr.Neo.11004721
1340rpm am Kopf.
12S
7Kg.
Benda 5 Blatt-Kopf ungedämpft.
Witte 630 Blätter 144g Symetrisch
Pitch max. 15grad.
Was meinst du zum Setup Rainer ?
Freundlicher Gruß
RV
8 June 2026 06:3208.06.2026 06:32
Well, I can draw parallels to my Roban Bell 429, which was also 7kg and undamped.
The cyclic value is negligible here; my Huey with 119 doesn't roll at full pitch - and the geometry of the 4-point 45° rotated linkage didn't offer anything else.
Your 89 are somewhat better, but as I said, that's not so relevant for the scaler.
Because of the short input – yes, you'll probably have to reduce the optimizers somewhat (to about 1/3 of the maneuverability) and control it more via the flight controller. It will then be less "sharp." Alternatively, there's the helicopter size, which you can increase, but it only has a limited effect.
The best option would be an EVO with a V8 engine - and then reduce the throttle response.
Because of the rebellion:
When I read that you're running 15 degrees of pitch, that tells me => too few RPM. This means you actually need high pitch values. I had about 12 degrees and 720-size blades on the 4-blade prop of my Bell. You'll reach a limit here where, during fast forward flight, the retreating blade needs such a large angle to maintain airspeed that the airflow stalls. The helicopter will pitch up.
- Check the cyclic ring (Could there be more movement in the end position?)
- Set pitch adjustment (normally 35) to approximately 20.
and if it still resists:
- less pitch
- higher speed
- longer blades to get by with the RPM here
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 08.06.2026 06:33 von RV.
Also - da kann ich parallelen zu meiner Bell 429 von Roban ziehen, die war auch 7kg und ungedämpft.
Der zyklische Wert ist hier vernachlässigbar, meine Huey mit 119 macht ja keine Rollen bei Vollpitch - und die Geoemtrie der 4-Punkt 45° gedrehten Anlenkung gab auch nix anderes her.
Deine 89 sind da schon was besser, ist aber wie gesagt beim Scaler erstmal net so relevant.
Wegen dem kurzen Input - ja, da musst Du vermutlich die Optimierer was zurücknehmen (ca. 1/3 der Wendigkeit nur) und mehr über die Regelung steuern. ist dann halt weniger "Knackig". Ansonsten gibts noch die Heligröße, die kann man raufsetzten, hat aber nur begrenzten Einfluß.
Am Besten wäre eine EVO mit V8 - und da dann das Ansprechverhalten runter.
Wegen dem Aufbäumen:
Wenn ich lese dass Du 15 Grad Pitch anstehen hast zeigt mir das => zuwenig RPM. Das hat zur Folge dass Du hohe Pitchwerte an sich schon brauchst. Ich hatte so ca, 12 Grad und 720er Blätter beim 4-Blatt der Bell oben. Du wirst hier in einen Grenzbereich kommen wo beim schnellen Vorwärtsflug das rücklaufende Blatt aufgrund der Fahrterhaltung so viel Winkel braucht dass die Strömung abreißt. Der Heli bäumt auf.
- Zyklischen Ring prüfen (Könnte da noch was gehen in der Endlage?)
- Pitch Anpassung (normal 35) auf ca. 20 stellen
und wenns dann immer noch aufbäumt:
- weniger Pitch
- mehr Drehzahl
- längere Blätter um mit der RPM hier auszukommen
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 08.06.2026 06:33 von RV.
Chriss
8 June 2026 06:4308.06.2026 06:43
Thank you Rainer for the information.
What do you mean by "- Set pitch adjustment (normally 35) to approximately 20"? In which menu?
Kind regards
Vielen Dank Rainer für die Info,
was meinst du mit "- Pitch Anpassung (normal 35) auf ca. 20 stellen " in welchen Menü ?
Freundlicher gruß
JMalberg
8 June 2026 11:2308.06.2026 11:23
Hey everyone,
A 15° pitch on a 5-blade propeller with Witte blades is too much; hardly any 3D helicopter flies with that pitch anyway.
Key data of my 7kg Hughes:
TDR 2009 in Hughes 500 approx. 7kg
ROBAN-5 blade (virtually no damping) therefore low gain (V8: 36)
Witte blades approx. 680mm
1450/min (the head wobbles at approximately 1400/min)
Maximum pitch approx. 12° with linear curve -90 -45 0 +45 +90
no noticeable resistance
brief, slight bouncing on Nick
Edith says:
Witte blades approx. 680mm
Rear blades approx. 120mm
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Edited twice. Last edited on June 8, 2026 at 10:30 PM by JMalberg.
Moin Leute,
15° Pitch an einem 5-Blatt mit Witte-Blättern ist zu viel; mit dem Pitch fliegt ja auch kaum ein 3D-Heli.
Kerndaten meiner 7kg-Hughes:
TDR 2009 in Hughes 500 ca 7kg
ROBAN-5-Blatt (nahezu keine Dämpfung) deshalb geringes Gain (V8: 36)
Witte-Blätter ca 680mm
1450/min (bei ca 1400/min wobbelt der Kopf)
Pitch max ca 12° mit linearer Kurve -90 -45 0 +45 +90
kein merkbares Aufbäumen
kurzes leichtes Nachwippen auf Nick
Edith sagt:
Witte-Blätter ca 680mm
Heckblätter ca 120mm
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
2 mal bearbeitet. Zuletzt am 08.06.2026 22:30 von JMalberg.
Chriss
8 June 2026 18:5008.06.2026 18:50
Hello Jürgen,
You say "a short, slight bounce on Nick" - why does it do that?
Do you also have the 630 Witte leaves?
They are extremely narrow in terms of leaf depth, which is why the pitch is so high.
Jürgen, what's your flying style like with your Huhges?
So, for example, I'm already using my somewhat more dynamic on-the-go role.
Kind regards
Hallo Jürgen,
du sagst "kurzes leichtes Nachwippen auf Nick" warum macht ist das so ?
Hast du auch die 630 Witte Blätter ?
Die sind halt schon extrem schmal von der Blatttiefe, deswegen ist der Picht so hoch.
Jürgen wie ist dein Flugstiel mit deiner Huhges ?
Also ich bin mit meiner schon etwas Dynamischer Unterwegs Rolle z.b.
Freundlicher Gruß
Chriss
8 June 2026 18:5408.06.2026 18:54
Hello Rainer,
In your setup video for multi-blade heads, the TS rotation is performed first, followed by the cyclic 8-degree calibration.
What happens if the calibration comes first, and then the TS rotation?
Does that matter?
Kind regards
Hallo Rainer,
in deinen Setup Video für Mehrblatt Köpfe, wird erst die TS drehehung gemacht und dann die Zykliche 8grad Kalibrierung.
Was ist wenn erst die Kaliebrierung kommt und dann die TS drehung ?
Ist das egal ?
Freundlicher Gruß
RV
8 June 2026 19:4708.06.2026 19:47
That doesn't really matter – but for the 8° measurement, you always have to take the point with the highest roll deflection. So... either find that point "unrotated" – or find it as usual on the roll axis with a static 90° rotation.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Das ist an sich egal - für die 8° Messung musst Du aber immer den Punkt mit dem höchsten Ausschlag bei Roll nehmen dann. Insofern ... entweder diesen "ungedreht" suchen - oder mit statischer Drehung auf die 90° Vorlauf wie gewohnt in der Rollachse finden ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
8 June 2026 19:4908.06.2026 19:49
Addition:
If the Witte blades are rather short and narrow, as in this case, they need higher RPM to prevent them from getting into "break-off positions". That's why Jürgen has 200 RPM more at the start.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Ergänzung:
Wenn die Witte Blätter so wie hier eher kurz und schmal sind - brauchen sie halt Drehzahl damit man nicht in "abrissfähige Anstellungen" kommt. So hat ja Jürgen nicht umsonst 200 1/min mehr am Start.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
JMalberg
8 June 2026 22:3608.06.2026 22:36
Chriss wrote:
-------------------------------------------------------
> You say "a short, slight bounce on Nick" - why does that happen?
I'll take care of it when it bothers me, since it's only an academic issue with Nick when hovering and not noticeable in flight.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Chriss schrieb:
-------------------------------------------------------
> du sagst "kurzes leichtes Nachwippen auf Nick" warum macht ist das so ?
Kümmere ich mich dann drum wenn es mich stört, da es nur akademisch bei Nick im Standschweben ist und im Flug nicht merkbar.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )