Tgilf
12 June 2026 17:2412.06.2026 17:24
Hi everyone. I removed the MSH Brain and set everything up with the Vbar Evo at my leisure. So far, so good.
When I connect the motor cables and insert the battery, the motor beeps continuously and I get an error message: "Controller error code set, check log." The log shows: "OMP ESC power-on test / throttle zero test." What am I doing wrong? So far, I've been using the OMP ESC's internal governor...
I set the gas to 40 for bank 1, 50 for bank 2, and 60 for bank 3...
Thank you for your help!
Tom
Hallo zusammen. Ich habe das MSH Brain entfernt und alles mit dem Vbar Evo in Ruhe eingerichtet. Soweit so gut.
Wenn ich nun die Motor Kabel anstecke und den Akku einlege piept der Motor ununterbrochen und es kommt eine Fehlermeldung: "Regler Fehlercode gesetzt Log prüfen" im Log steht: "OMP ESC Einschalt Test / Gasnull test" Was mache ich falsch? Bisher habe ich den internen Governor vom OMP ESC benutzt...
Gas habe ich Bank 1 40 Bank 2 50 und Bank 3 60 gesetzt...
Danke für eure Hilfe!
Tom
RV
12 June 2026 17:5012.06.2026 17:50
Hi Tom,
The controller should normally automatically detect and adjust itself using Mikado telemetry.
How was it put into operation?
After the controller was connected via Tele, was the corresponding HW Mode selected and sent over in the model setup?
Is the controller also connected to the ESC?
Do you perhaps have the motor switch on a push-button switch instead of a 3-way switch?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hallo Tom,
der Regler muss normalerweise von selbst Mikado Telemetrie erkennen und sich einstellen.
Wie wurde denn das in Betrieb genommen?
Wurde auch nachdem der Regler über Tele dann dran war im Modell Setup der entspr. HW Mode ausgewählt und rübergeschickt?
Ist der Regler auch an ESC dran?
Hast Du möglicherweise den Motorschalter auf einem Tastschalter statt 3-Wege-Schalter?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Tgilf
12 June 2026 18:0212.06.2026 18:02
Thanks Rainer,
In the model setup, I selected the external ESC governor. The ESC is connected to the Vbar Evo's ESC connector (black wire at the bottom, white wire at the top). I've connected the telemetry cable to the front connector on the side. It's transmitting the values, but it's beeping constantly. Should I try switching from StorGovernor to the Vstabi governor using the OMP Bluetooth module?
I've set the motor switch to switch 5 and the safety switch to switch 6. I've also activated bank 4, which is then autorotation in the middle position of switch 5...
Many thanks!!
Danke Rainer,
Ich habe im Modell Setup den ESC Governor extern gewählt. Der Regler hängt am Vbar Evo am ESC anschluss schwarz unten weiss oben. Seitlich habe ich das Telemetrie Kabel angesteckt an den vorderen Anschluss. Die Werte überträgt er auch. Er piept halt ununterbrochen. Soll ich mit dem OMP Bluetooth Modul mal von StorGovernor umstellen und den Governor vom vstabi benutzen?
Den Motorschalter habe ich auf den Schalter 5 und Sicherheit auf Schalter 6. Bank 4 habe ich auch aktiviert der Ist dann Autorotation in der Mitte vom Schalter 5...
Danke vielmals!!
RV
12 June 2026 19:1512.06.2026 19:15
Okay - that looks good.
Was an output frequency also set for the controller in the setup? If so, which one?
Could you connect a servo to the ESC (then connect the controller to, for example, AUX3) and see if it moves when the motor switch is turned on?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Okay - das sieht gut aus.
Wurde auch im Setup eine Ausgabefrequenz an den Regler eingestellt? Welche dann?
Kannst Du mal ein Servo an ESC (Regler dann an z.B. AUX3) anschließen und schauen ob das sich bewegt beim Umschalten des Motorschalters?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Tgilf
12 June 2026 21:0412.06.2026 21:04
I had selected 72Hz / 1500 / 1520µs and then increased it to 333 Hz...
I've made progress. If I change the endpoint setting in the menu controller output setting from 100 to 115 for the "Off" endpoint, then everything initializes and I can start the motor.
With my previous transmitter (Spektrum NX 10), I had to start at 100% throttle to calibrate the endpoints with a linear throttle curve in order to calibrate the controller to the throttle range. Do I have to repeat this process? If so, how do I do it with Vbar?
At 40 throttle, it's running at almost 1800 rpm, if the reading is correct – with my Spektrum and the Brain, it was around 1400-1500 rpm... I think something's still wrong here...
Ich hatte 72Hz / 1500 / 1520us ausgewähltl und es eben auf 333 Hz erhöht...
Ich habe einen Fortschritt erzielt. Wenn ich die Endpunkte beim Menü Regler Ausgabeeinstellung beim Endpunkt "Aus" von 100 auf 115 stelle dann initialisiert alles und ich kann den Motor starten.
Beim meinem vorherigen Sender ( Spektrum NX 10 ) habe ich zum kalibrieren der Endpunkte mit linearer Gaskurve bei 100 Gas starten müssen um den Regler zu kalibrieren auf den Gasweg. Muss ich das nochmal wiederholen - wenn ja wie geht es mit der Vbar.
Bei 40 Gas hat er fast 1800rpm falls die Anzeige stimmt - bei meiner Spektrum mit dem Brain waren es da ca. 1400-1500rpm... denke hier läuft noch was falsch...
RV
12 June 2026 23:4612.06.2026 23:46
So:
As already mentioned, the HW ESC MUST automatically set OUR throttle paths when it detects the Mikado Tele. Therefore, this fiddling around is unnecessary.
If it doesn't, it could be because it either doesn't recognize Mikado (but then there would be no telemetry) or hasn't had its mode reset.
Now we're going to do the following: we're switching to VGov. Please ONLY do this:
- Leaves down (all)
- Ensure that the RPM connection of the controller is also connected to the RPM input of the stabilizer.
- Gas passages restored to original
- Safety switch in the "On" position - don't let it spit in us.
- Motor switch in "Off"
- In VBar Setup - Change Setup - Scroll all the way down the display
- Reset controller mode to VBar speed control (Is the button with the HW icon there then?)
- Check gear ratio and number of poles (should match)
- Unplug the model, plug it in 10 seconds later
- In the flight panel (2nd page of the main screen, scroll down), set a sensible RPM as the target for each bank.
- Start the engine and see if it works now (It's possible that the lowest target RPM could now be slightly exceeded due to the lack of load)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Also:
Wie schon geschrieben MUSS der HW ESC UNSERE Gaswege automatisch setzen wenn er Mikado Tele erkennt. Insofern ist das Gedaddel nicht notwendig.
Tut er das nicht - kann es daran liegen dass er entweder nicht Mikado erkennt (aber dann gäbe es auch keine Telemetrie) oder keinen Modus neu gesetzt bekommen hat.
Jetzt machen wir mal folgendes, wir stellen auf VGov um, bitte NUR das tun:
- Blätter runter (alle)
- Sicherstellen dass der RPM Anschluss des Reglers auch am RPM Eingang der Stabi dran ist
- Gaswege wieder Original
- Sicherheitsschalter auf Stellung für "Ein" - nicht dass der uns reinspuckt.
- Motorschalter auf "Aus"
- In der VStabi Setup - Setup ändern - Anzeige ganz runterscrollen
- Reglermodus neu setzen auf VStabi Drehzahlregelung (Ist dort der Button mit HW Icon dann?)
- Getriebeübersetzung und Polzahl prüfen (sollte passen)
- Modell abstecken, 10s später anstecken
- im Flugpanel (2. Seite Mainscreen, runterscrollen) sinnvolle RPM als Soll pro Bank einstellen
- Motor ein und schauen ob das nun geht (Möglicherweise könnte aufgrund fehlender Last nun die niedrigste Soll RPM etwas übetroffen werden)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Tgilf
13 June 2026 10:3513.06.2026 10:35
Good morning
I followed those instructions exactly. It's an OMP controller, by the way, and the symbol is correct.
After switching to Vbar governor, the engine started immediately at approximately 400 RPM, despite the engine being off and safety being activated... after restarting, the same error message appeared again with "ESC start throttle 0 test"...
Guten Morgen.
Habe ich exakt so durchgeführt. Es ist übrigens ein OMP Regler und das Symbol ist korrekt.
Nach dem umstellen auf Vbar governor ging trotz Motor aus und Sicherheit der Motor direkt an mit ca. 400 Umdrehungen... nach dem Neustart dann wieder die selbe Fehlermeldung mit "ESC Einschalt Gas 0 test"...
RV
13 June 2026 10:4113.06.2026 10:41
Aha... strange. Looks like OMP must have been asleep when they read our specs. But somehow I'm not too surprised ;-(
But then, just adjust the gas lines as an exception.
What happens when you set an RPM and turn it on – does it still reach that speed?
Since we are unloaded and have no leaves, please use a high RPM, otherwise it might not regulate itself.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 13.06.2026 10:42 von RV.
Aha ... komisch. Da hat OMP dann wohl beim lesen unserer Spec geschlafen. Wundert mich nun aber irgendwie auch nicht zu sehr ;-(
Aber dann passe einfach erstmal die Gaswege ausnahmsweise an.
Wie sieht es denn dann aus wenn Du eine RPM einstellst und anmachst - wird diese auch dann angefahren?
Da wir lastfrei ohne Blätter sind bitte eine hohe RPM nehmen, könnte sich sonst ev. nicht einregeln.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 13.06.2026 10:42 von RV.
Tgilf
13 June 2026 11:0413.06.2026 11:04
I disconnected the engine again and restarted it. Now it worked with the Vbar Governor. A few questions about that, Rainer:
1. It slowly ramps up to 1400 rpm, and then when I apply full or negative pitch, the speed increases to 1700 rpm? (without blades on the table) Is that normal?
2. When I assign AR to bank 4 in the bank management settings, it sets the throttle to 17%, which corresponds to approximately 600 rpm – why? I thought there shouldn't be any throttle applied during AR? Regardless of the fact that I haven't mastered the maneuver :-)
3. Do you think I can fly it like this? Or should I switch back to the OMP ESC Gov Store?
Thank you so much for the always prompt help!! Really great!
Nochmal Motor abgeklemmt neu gestartet. Jetzt ging es mit dem Vbar Governor. Ein paar Fragen dazu Rainer:
1. Er läuft langsam hoch bis 1400rpm wenn ich dann Pitch voll oder negativ gebe geht die Drehzahl hoch auf 1700? (ohne Blätter auf dem Tisch) ist das normal?
2. Wenn ich im Bankmanagement die AR auf Bank 4 Lege gibt er bei den Einstellungen dort 17% Gas vor was ca 600rpm entspricht - warum? Ich dachte bei AR soll kein Gas anliegen? Unabhängig davon das ich das Manöver nicht beherrsche :-)
3. Meinst du ich kann ihn so fliegen? Oder soll ich wieder auf den OMP ESC Gov Stor zurückschalten?
Vielen Dank für die immer prompte Hilfe!! Richtig toll
RV
13 June 2026 17:1713.06.2026 17:17
1 - normal, that's the gas curve in the background. More info about our Gov:
https://www.vstabi.info/de/node/2033 2 - equally okay, revs up faster if the controller is still in commutation
Everything fits!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 - normal, das ist die Gaskurve im Hintergrund. Mehr infos zu unserem Gov:
https://www.vstabi.info/de/node/2033
2 - ebenso okay, dreht schneller wieder hoch wenn der Regler noch in Kommutierung ist
Passt alles!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Tgilf
13 June 2026 18:2013.06.2026 18:20
Thank you!!!
Vielen Dank!!!