Tgilf
13 August 2026 07:5413.08.2026 07:54
Hello everyone!
Perhaps an unusual question, but I have a Vstabi EVO in my OMP M4 max and would like to use it for the RAW 700 which is still under construction, also because of the 12V servos used there.
Can I export the EVO configuration and import it into the NEO which will then go into the M4 Max, or should I "set everything up from scratch"?
Thank you
Tom
Hallo zusammen!
Vielleicht ungewöhnliche Frage, aber ich habe ein Vstabi EVO im OMP M4 max und möchte dieses für den noch im Aufbau befindlichen RAW 700 benutzten, auch aufgrund der dort zum Einsatz kommenden 12V Servos.
Kann ich die Konfiguration des EVO exportieren und in das NEO welches dann in den M4 Max kommt importieren oder sollte man alles "neu aufsetzen".
Vielen Dank
Tom
Eddi E. aus G.
13 August 2026 09:0113.08.2026 09:01
Hi Tom,
No, please don't. I'm not a fan of transferring setups anyway, unless it's a 1:1 transfer from the same VBar and version to the same VBar and version on your own helicopter, but V8 or V7 to V6 is almost certainly going to go wrong.
Such a setup can be completed in no time at all for an existing helicopter.
If you've flown in some special things, you can add them back in (writing them down beforehand or taking screenshots can help).
But some parameters are not available in the older version, or they work differently, are scaled differently.
And sometimes, after a new setup, you wonder why the helicopter suddenly flies so well... because you might have gotten lost before.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Tom,
nein, bitte nicht. Ich bin sowieso kein Fan von Setups übertragen, außer es ist auf dem eigenen Heli 1:1 von gleicher VStabi und Version auf gleiche VStabi und Version, aber V8 oder V7 nach V6, geht ziemlich sicher schief.
So ein Setup ist für einen bestehenden Heli doch in Nullkommanix durchgeklickt.
Wenn man besondere Dinge erflogen hat, kann man die ja auch wieder eindrehen (vorher abschreiben oder Screenshots machen kann helfen).
Aber manche Parameter gibt's auch in der älteren Version nicht, oder sie funktionieren anders, sind anders skaliert.
Und manchmal wundert man sich nach einem neuen Setup auch, warum der Heli plötzlich so gut fliegt ... weil man sich vorher vielleicht verlaufen hatte.
Grüßle
Eddi
Born to fly ...
forced to work.
Tgilf
13 August 2026 09:1913.08.2026 09:19
Thanks a lot, Eddi! That helps me a lot. You're right, it actually goes pretty quickly... Do I need to reset the EVO then? Or is creating a new model enough?
Vielen Dank Eddi! Das hilft mir doch sehr weiter. Du hast schon Recht, eigentlich geht es flott... Muss ich das EVO dann zurücksetzen? Oder reicht ein neues Modell erstellen aus?
Eddi E. aus G.
13 August 2026 09:3713.08.2026 09:37
Hi,
A new setup is essentially a factory reset, in which all parameters are assigned known good values (and tailored to the model/model size).
When you select a controller type (VBar/External Controller) in the setup, default parameters are set for it.
If a known controller with telemetry is used, it will be automatically set correctly (e.g. YGE with VBar Governor), but the gear ratio and motor pole count are still needed, as always.
In the end, all that's left to do is set the servo rotation directions correctly, trim the swashplate horizontally, set the pitch and 8° cyclic limits, set the tail limits, ... and go flying :-)
Are you still hiring, or are you already flying? :-)
If macrocells were programmed for special functions, you would have to treat them separately, but this is rather unusual for helicopters or trainers.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
ein neues Setup ist quasi ein Werksreset, dabei werden alle Parameter mit bekannt guten (und für das Modell/die Modellgröße abgestimmten) Werten belegt.
Wenn man im Setup einen Regler-Typ auswählt (VStabi/Externer Regler) werden Standard-Parameter dafür gesetzt.
Wenn ein bekannter Regler mit Telemetrie in Verwendung ist, wird der auch automatisch richtig eingestellt (bspw. YGE mit VStabi Governor), Übersetzung und Motor-Polzahl braucht's halt, wie immer.
Am Ende bleibt ja fast nur, Servo-Drehrichtungen richtig einstellen, Taumelscheibe waagrecht trimmen, Limits für Pitch und 8° zyklisch einstellen, Heck-Limits einstellen, ... fliegen gehen :-)
#stellst Du noch ein, oder fliegst Du schon? :-)
Falls Makrozellen für Sonderfunktionen programmiert wären müsstest Du die separat behandeln, ist beim Heli respektive beim Trainer aber eher unüblich.
Grüßle
Eddi
Born to fly ...
forced to work.
Tgilf
13 August 2026 10:1713.08.2026 10:17
Thank you so much!! Absolutely fantastic – both the products and the support are worth every penny! :-)
Tausend Dank!! Wirklich super - sowohl die Produkte als auch der Support jeden cent Wert! :-)