Hello everyone,
First, let me describe my setup:
Goosky RS7 Ultra
Xnova 4030-710
YGE Sapphire 125
MKS 650/680 Low Profile
SLS 8s 4000 40c
EVO 8.1
All this with a takeoff weight of 4.2 kg; rotational speeds: 1540/1720/1900, mostly flown at 1720, light 3D; sporty circular flight.
Now to my problem/question:
As can be seen from the attachment, everything looks good during the flight shown, except for the fact that one second before switching off (the helicopter had already landed), the message appeared.
The log shows the YGE current limit being reached . Other data points include Umin 28.5, Imax 91.0A and Temp 54, so everything is within normal limits.
Question: Is this possibly a bug in the controller or the Vstabi software in connection with the controller?
I get this message on almost every flight now.
In addition to the VBackup (3x25), I also installed a 10000 buffer from Jeti.
(https://www.hacker-motor-shop.com/Drehzahlregler-und-Zubehoer/Regler-Zubehoer/JETImodel-Addcap-10AS.htm?a=article&ProdNr=22985481&p=10694)
to reduce back currents to the BEC.
The controller never got hot, nor did the servos. The maximum current output before the YGE controller throttled down was set to 200 A.
Has anyone else experienced a similar/the same message?
Thanks, best regards, Christian
07/12/2026 6:00:14 p.m.;VBar Start -- RS 7 ULTRA -- 0027005430 -- V 8.2 -- pl 40
12/07/2026 18:00:14 Good; Cold start
12/07/2026 18:00:14 Good; Reset Reason: Power On
12.07.2026 18:00:14 Good; Bank 1 loaded
12/07/2026 18:00:15 Good; VBackup device detected
12.07.2026 18:00:15 Good; Backup connected, cap: 0.0V
12/07/2026 18:00:18 Good; YGE controller detected
07/12/2026 6:00:20 p.m. Good; Fixed battery ID: 0027005430
12/07/2026 18:00:20 Good; Battery data from VBC: SLS 4000 8s
12/07/2026 18:00:20 Good; Calibration complete
12/07/2026 18:00:27 Good; VBackup in standby
12.07.2026 18:01:00 Good; Backup minimum ready, cap: 6.6V
12.07.2026 18:01:27 Good;VBackup connected, cap:8.1V
12.07.2026 18:01:30 Info; Speed controller switched ON
12/07/2026 18:01:31 Good; Motor switch Motor On
12.07.2026 18:08:19 Good; Bank 4 loaded
12/07/2026 18:08:19 Warning; YGE power limit reached
12.07.2026 18:08:20 Info; Speed controller switched to OFF
12/07/2026 18:08:20 Good; Motor switch Motor Off
12.07.2026 18:08:20 Info; Off - Regulator - Umin: 28.5V Imax: 91.0A Temp: 54°
12/07/2026 18:08:32 Good; VBackup in standby
12.07.2026 18:09:08 Good;VBackup connected, cap:8.0V
12/07/2026 18:09:20 Good; Backup in standby
07/12/2026 6:09:40 p.m.;VBar Logfile End -- 07/12/2026 -- 6:09:40 p.m
12/07/2026 18:09:40 Good;VBackup Consumed: 7mAh
12/07/2026 18:09:40 Good;VBackup Separated
12.07.2026 18:09:40 Good; YGE Controller Separated
Edited 4 times. Last edited on 18.07.2026 at 08:31 by cc1975.
First, let me describe my setup:
Goosky RS7 Ultra
Xnova 4030-710
YGE Sapphire 125
MKS 650/680 Low Profile
SLS 8s 4000 40c
EVO 8.1
All this with a takeoff weight of 4.2 kg; rotational speeds: 1540/1720/1900, mostly flown at 1720, light 3D; sporty circular flight.
Now to my problem/question:
As can be seen from the attachment, everything looks good during the flight shown, except for the fact that one second before switching off (the helicopter had already landed), the message appeared.
The log shows the YGE current limit being reached . Other data points include Umin 28.5, Imax 91.0A and Temp 54, so everything is within normal limits.
Question: Is this possibly a bug in the controller or the Vstabi software in connection with the controller?
I get this message on almost every flight now.
In addition to the VBackup (3x25), I also installed a 10000 buffer from Jeti.
(https://www.hacker-motor-shop.com/Drehzahlregler-und-Zubehoer/Regler-Zubehoer/JETImodel-Addcap-10AS.htm?a=article&ProdNr=22985481&p=10694)
to reduce back currents to the BEC.
The controller never got hot, nor did the servos. The maximum current output before the YGE controller throttled down was set to 200 A.
Has anyone else experienced a similar/the same message?
Thanks, best regards, Christian
07/12/2026 6:00:14 p.m.;VBar Start -- RS 7 ULTRA -- 0027005430 -- V 8.2 -- pl 40
12/07/2026 18:00:14 Good; Cold start
12/07/2026 18:00:14 Good; Reset Reason: Power On
12.07.2026 18:00:14 Good; Bank 1 loaded
12/07/2026 18:00:15 Good; VBackup device detected
12.07.2026 18:00:15 Good; Backup connected, cap: 0.0V
12/07/2026 18:00:18 Good; YGE controller detected
07/12/2026 6:00:20 p.m. Good; Fixed battery ID: 0027005430
12/07/2026 18:00:20 Good; Battery data from VBC: SLS 4000 8s
12/07/2026 18:00:20 Good; Calibration complete
12/07/2026 18:00:27 Good; VBackup in standby
12.07.2026 18:01:00 Good; Backup minimum ready, cap: 6.6V
12.07.2026 18:01:27 Good;VBackup connected, cap:8.1V
12.07.2026 18:01:30 Info; Speed controller switched ON
12/07/2026 18:01:31 Good; Motor switch Motor On
12.07.2026 18:08:19 Good; Bank 4 loaded
12/07/2026 18:08:19 Warning; YGE power limit reached
12.07.2026 18:08:20 Info; Speed controller switched to OFF
12/07/2026 18:08:20 Good; Motor switch Motor Off
12.07.2026 18:08:20 Info; Off - Regulator - Umin: 28.5V Imax: 91.0A Temp: 54°
12/07/2026 18:08:32 Good; VBackup in standby
12.07.2026 18:09:08 Good;VBackup connected, cap:8.0V
12/07/2026 18:09:20 Good; Backup in standby
07/12/2026 6:09:40 p.m.;VBar Logfile End -- 07/12/2026 -- 6:09:40 p.m
12/07/2026 18:09:40 Good;VBackup Consumed: 7mAh
12/07/2026 18:09:40 Good;VBackup Separated
12.07.2026 18:09:40 Good; YGE Controller Separated
Edited 4 times. Last edited on 18.07.2026 at 08:31 by cc1975.
Hallo in die Runde,
zunächst zu meinem Setup:
Goosky RS7 Ultra
Xnova 4030-710
YGE Saphir 125
MKS 650/680 Low Profile
SLS 8s 4000 40c
EVO 8.1
Das Ganze bei 4,2 KG Abfluggewicht; Drehzahlen: 1540/1720/1900, überwiegend wird mit 1720 geflogen, leichtes 3D; sportlicher Rundflug.
Jetzt zu meinem Problem/Frage:
Wie aus dem Anhang ersichtlich, sieht bei dem gezeigten Flug alles gut aus bis auf den Umstand, das 1 Sekunde vor dem Ausschalten (Heli war schon gelandet), die Meldung
YGE Stromlimit erreicht im Log erscheint. Als weitere Daten werden Umin 28,5; Imax 91,0A und Temp 54 angegeben, also alles im grünen Bereich.
Frage: Ist das eventuell ein Bug seitens des Reglers oder der Vstabi Software im Zusammenhang mit dem Regler?
Diese Meldung bekomme ich eigentlich fast in jedem Flug mittlerweile.
Zusätzlich zum VBackup (3x25) habe ich noch einen 10000er Puffer von Jeti verbaut.
(https://www.hacker-motor-shop.com/Drehzahlregler-und-Zubehoer/Regler-Zubehoer/JETImodel-Addcap-10AS.htm?a=article&ProdNr=22985481&p=10694)
zur Reduzierung der Rückstrome zum BEC.
Der Regler wurde nie heiß, ebenso die Servos nicht. Die maximale Stromausgabe bis zum Runterregeln beim YGE wurde auf 200 A gesetzt.
Hat jemand ähnliche/die Gleiche Meldung bei sich beobachten können?
Danke Gruß Christian
12.07.2026 18:00:14;VStabi Start -- RS 7 ULTRA -- 0027005430 -- V 8.2 -- pl 40
12.07.2026 18:00:14 Gut;Kaltstart
12.07.2026 18:00:14 Gut;Reset Grund: Power On
12.07.2026 18:00:14 Gut;Bank 1 geladen
12.07.2026 18:00:15 Gut;VBackup Gerät erkannt
12.07.2026 18:00:15 Gut;VBackup verbunden, cap:0.0V
12.07.2026 18:00:18 Gut;YGE Regler erkannt
12.07.2026 18:00:20 Gut;Feste Akku ID: 0027005430
12.07.2026 18:00:20 Gut;Akkudaten von VBC: SLS 4000 8s
12.07.2026 18:00:20 Gut;Kalibrierung beendet
12.07.2026 18:00:27 Gut;VBackup im Standby
12.07.2026 18:01:00 Gut;VBackup minimum bereit, cap:6.6V
12.07.2026 18:01:27 Gut;VBackup verbunden, cap:8.1V
12.07.2026 18:01:30 Info;Drehzahlregler auf AN geschaltet
12.07.2026 18:01:31 Gut;Motorschalter Motor An
12.07.2026 18:08:19 Gut;Bank 4 geladen
12.07.2026 18:08:19 Warn;YGE Stromlimit erreicht
12.07.2026 18:08:20 Info;Drehzahlregler auf AUS geschaltet
12.07.2026 18:08:20 Gut;Motorschalter Motor Aus
12.07.2026 18:08:20 Info;Aus - Regler - Umin:28.5V Imax:91.0A Temp:54°
12.07.2026 18:08:32 Gut;VBackup im Standby
12.07.2026 18:09:08 Gut;VBackup verbunden, cap:8.0V
12.07.2026 18:09:20 Gut;VBackup im Standby
12.07.2026 18:09:40;VBar Logfile End -- 12.07.2026 -- 18:09:40
12.07.2026 18:09:40 Gut;VBackup Verbraucht: 7mAh
12.07.2026 18:09:40 Gut;VBackup Getrennt
12.07.2026 18:09:40 Gut;YGE Regler Getrennt
4 mal bearbeitet. Zuletzt am 18.07.2026 08:31 von cc1975.
zunächst zu meinem Setup:
Goosky RS7 Ultra
Xnova 4030-710
YGE Saphir 125
MKS 650/680 Low Profile
SLS 8s 4000 40c
EVO 8.1
Das Ganze bei 4,2 KG Abfluggewicht; Drehzahlen: 1540/1720/1900, überwiegend wird mit 1720 geflogen, leichtes 3D; sportlicher Rundflug.
Jetzt zu meinem Problem/Frage:
Wie aus dem Anhang ersichtlich, sieht bei dem gezeigten Flug alles gut aus bis auf den Umstand, das 1 Sekunde vor dem Ausschalten (Heli war schon gelandet), die Meldung
YGE Stromlimit erreicht im Log erscheint. Als weitere Daten werden Umin 28,5; Imax 91,0A und Temp 54 angegeben, also alles im grünen Bereich.
Frage: Ist das eventuell ein Bug seitens des Reglers oder der Vstabi Software im Zusammenhang mit dem Regler?
Diese Meldung bekomme ich eigentlich fast in jedem Flug mittlerweile.
Zusätzlich zum VBackup (3x25) habe ich noch einen 10000er Puffer von Jeti verbaut.
(https://www.hacker-motor-shop.com/Drehzahlregler-und-Zubehoer/Regler-Zubehoer/JETImodel-Addcap-10AS.htm?a=article&ProdNr=22985481&p=10694)
zur Reduzierung der Rückstrome zum BEC.
Der Regler wurde nie heiß, ebenso die Servos nicht. Die maximale Stromausgabe bis zum Runterregeln beim YGE wurde auf 200 A gesetzt.
Hat jemand ähnliche/die Gleiche Meldung bei sich beobachten können?
Danke Gruß Christian
12.07.2026 18:00:14;VStabi Start -- RS 7 ULTRA -- 0027005430 -- V 8.2 -- pl 40
12.07.2026 18:00:14 Gut;Kaltstart
12.07.2026 18:00:14 Gut;Reset Grund: Power On
12.07.2026 18:00:14 Gut;Bank 1 geladen
12.07.2026 18:00:15 Gut;VBackup Gerät erkannt
12.07.2026 18:00:15 Gut;VBackup verbunden, cap:0.0V
12.07.2026 18:00:18 Gut;YGE Regler erkannt
12.07.2026 18:00:20 Gut;Feste Akku ID: 0027005430
12.07.2026 18:00:20 Gut;Akkudaten von VBC: SLS 4000 8s
12.07.2026 18:00:20 Gut;Kalibrierung beendet
12.07.2026 18:00:27 Gut;VBackup im Standby
12.07.2026 18:01:00 Gut;VBackup minimum bereit, cap:6.6V
12.07.2026 18:01:27 Gut;VBackup verbunden, cap:8.1V
12.07.2026 18:01:30 Info;Drehzahlregler auf AN geschaltet
12.07.2026 18:01:31 Gut;Motorschalter Motor An
12.07.2026 18:08:19 Gut;Bank 4 geladen
12.07.2026 18:08:19 Warn;YGE Stromlimit erreicht
12.07.2026 18:08:20 Info;Drehzahlregler auf AUS geschaltet
12.07.2026 18:08:20 Gut;Motorschalter Motor Aus
12.07.2026 18:08:20 Info;Aus - Regler - Umin:28.5V Imax:91.0A Temp:54°
12.07.2026 18:08:32 Gut;VBackup im Standby
12.07.2026 18:09:08 Gut;VBackup verbunden, cap:8.0V
12.07.2026 18:09:20 Gut;VBackup im Standby
12.07.2026 18:09:40;VBar Logfile End -- 12.07.2026 -- 18:09:40
12.07.2026 18:09:40 Gut;VBackup Verbraucht: 7mAh
12.07.2026 18:09:40 Gut;VBackup Getrennt
12.07.2026 18:09:40 Gut;YGE Regler Getrennt
4 mal bearbeitet. Zuletzt am 18.07.2026 08:31 von cc1975.
machine-translated from German · Show original