Good morning,
I'm currently building an XLPower Specter 700 V2 Ultimate. The VBar EVO will be mounted on the rear platform, and the YGE Aureus 135 on the front ESC platform. The Power Backup would also be a convenient option for the front, under the ESC. I've noticed that the Power Backup allows for telemetry pass-through and also includes a servo signal wire in addition to the power supply. I'm considering connecting the YGE telemetry via an adapter cable to the Power Backup daisy chain port and sending the RPM signal through the Power Backup's servo signal. It seems the Power Backup doesn't process the servo signal; it simply passes it through end-to-end.
1. Would that work?
2. Could there be any problems with this procedure that I'm overlooking, for example, in case of an error, if ESC fails and the backup is needed?
Is it okay to mix the ESC telemetry with the power backup telemetry? The VBar governor uses the RPM signal for its control. So, if the ESC telemetry is slower because it shares a line with the power backup, that wouldn't have any effect, right?
Thank you and best regards
Christian
Best regards
Christian
I'm currently building an XLPower Specter 700 V2 Ultimate. The VBar EVO will be mounted on the rear platform, and the YGE Aureus 135 on the front ESC platform. The Power Backup would also be a convenient option for the front, under the ESC. I've noticed that the Power Backup allows for telemetry pass-through and also includes a servo signal wire in addition to the power supply. I'm considering connecting the YGE telemetry via an adapter cable to the Power Backup daisy chain port and sending the RPM signal through the Power Backup's servo signal. It seems the Power Backup doesn't process the servo signal; it simply passes it through end-to-end.
1. Would that work?
2. Could there be any problems with this procedure that I'm overlooking, for example, in case of an error, if ESC fails and the backup is needed?
Is it okay to mix the ESC telemetry with the power backup telemetry? The VBar governor uses the RPM signal for its control. So, if the ESC telemetry is slower because it shares a line with the power backup, that wouldn't have any effect, right?
Thank you and best regards
Christian
Best regards
Christian
Moin,
ich baue gerade einen XLPower Specter 700 V2 Ultimate auf. Das VStabi EVO kommt hinten auf die Heckplattform, der YGE Aureus 135 vorne auf die ESC-Plattform. Nun würde sich das Power Backup ebenfalls vorne unter dem ESC anbieten. Ich habe gesehen, dass man beim Power Backup einerseits Telemetrie durchschleifen kann und andererseits in dem Servo-Kabel neben der Versorgung durch das Power Backup auch ein "Servo"-Signalkabel hat. Ich spiele nun mit dem Gedanken die YGE-Telemetrie per Adapterkabel einfach vorne am Power Backup Daisy Chain Port anzuschließen und das RPM-Signal über das "Servo"-Signal des Power-Backup zu senden. Das Servo-Signal wird ja scheinbar vom Power-Backup nicht ausgewertet, sondern einfach nur Ende-zu-Ende durchgeschliffen.
1. Würde das funktionieren?
2. Könnte es mit dem Vorgehen Probleme geben, die ich gerade übersehe, z.B. im Fehlerfall, wenn ESC ausfällt und das Backup gebraucht würde?
Ist es okay die ESC-Telemetrie mit der Power-Backup-Telemetrie zu mischen? Der VStabi Governor verwendet für die Regelung ja das RPM-Signal. Sollte die ESC-Telemetrie also z.B. langsamer sein, da sie sich eine Leitung mit dem Power-Backup teilt, würde sich das da ja nicht auswirken, oder?
Danke und viele Grüße
Christian
Viele Grüße
Christian
ich baue gerade einen XLPower Specter 700 V2 Ultimate auf. Das VStabi EVO kommt hinten auf die Heckplattform, der YGE Aureus 135 vorne auf die ESC-Plattform. Nun würde sich das Power Backup ebenfalls vorne unter dem ESC anbieten. Ich habe gesehen, dass man beim Power Backup einerseits Telemetrie durchschleifen kann und andererseits in dem Servo-Kabel neben der Versorgung durch das Power Backup auch ein "Servo"-Signalkabel hat. Ich spiele nun mit dem Gedanken die YGE-Telemetrie per Adapterkabel einfach vorne am Power Backup Daisy Chain Port anzuschließen und das RPM-Signal über das "Servo"-Signal des Power-Backup zu senden. Das Servo-Signal wird ja scheinbar vom Power-Backup nicht ausgewertet, sondern einfach nur Ende-zu-Ende durchgeschliffen.
1. Würde das funktionieren?
2. Könnte es mit dem Vorgehen Probleme geben, die ich gerade übersehe, z.B. im Fehlerfall, wenn ESC ausfällt und das Backup gebraucht würde?
Ist es okay die ESC-Telemetrie mit der Power-Backup-Telemetrie zu mischen? Der VStabi Governor verwendet für die Regelung ja das RPM-Signal. Sollte die ESC-Telemetrie also z.B. langsamer sein, da sie sich eine Leitung mit dem Power-Backup teilt, würde sich das da ja nicht auswirken, oder?
Danke und viele Grüße
Christian
Viele Grüße
Christian
machine-translated from German · Show original