← VBar Control Touch / EVO

VPlane, MacBook Air M4 and Heli V8 translated

VBar Control › VBar Control Touch / EVO · Started by Remo1984 on 22 March 2026 06:0922.03.2026 06:09
Remo1984 22 March 2026 06:0922.03.2026 06:09
Hello everyone

I've streamlined my fleet so I can fly with a much greater focus. Specifically, I now have a brand new EF E300 67" ready for construction, and I'm still waiting for the Logo 580 as its counterpart.

As a Futaba fan of over 25 years, I chose VBar as my only system due to its simplicity and reduction in equipment, since I've had the Evo transmitter lying around since I was waiting for the Logo 580… (and recently reduced my laptop setup to just a MacBook Air M4).

I ordered the basic receiver and a new stabilizer for the helicopter. I've already downloaded VPlane from the shop on the transmitter, and it looks like I've downloaded Heli V8 as well.

It should be starting now, but somehow it's not. The transmitter isn't updating the stabilizer to V8, and I can't select the aircraft type on the brand new Basic receiver (7.xx).

Last night I almost regretted my decision, but I'm sure I'm doing something wrong with my Futaba brain. What can you tell me?

Thank you :-)

Regards, Remo
machine-translated from German · Show original
Fingolf 22 March 2026 07:3122.03.2026 07:31
Hi,

What does your version say about the stabilization?
Did you change the account to V8?
Then the over-the-air update should work.

A basic receiver is "only" a receiver with which you can
then fly a plane, drive a car or boat, etc., but anyway
without stabilization.
It's best to connect a few servos and test them.
Reactions.

Stephan
machine-translated from German · Show original
thomas1130 22 March 2026 07:4822.03.2026 07:48
And what does all this have to do with a "MacBook Air M4"?
I don't quite understand that...
?

Best regards,
Thomas
machine-translated from German · Show original
Remo1984 22 March 2026 08:5322.03.2026 08:53
There is no software that allows me to connect Mikado transmitters or stabilizers to the MB Air M4 or my account.



Edited once. Last edited on 22.03.2026 at 08:59 by Remo1984.
machine-translated from German · Show original
Remo1984 22 March 2026 08:5822.03.2026 08:58
I have no devices in the account because there is no software to connect them to.

VBar Control Evo 2.1.125
NEO/EVO Version 7.1.30
Basic Receiver 7.1.30 (the part looks exactly the same and is displayed as NEO/EVO version).
machine-translated from German · Show original
Remo1984 22 March 2026 09:0122.03.2026 09:01
Exactly, that's what I want too. Simply program the Extras with the Basic Receiver.
LG
machine-translated from German · Show original
Fingolf 22 March 2026 10:3022.03.2026 10:30
You don't need any software for that.
Log in to vstabi.info, then connect to the stabilizer, view the status, and update via QR code.
Get it with your smartphone and register the device for your account.
Then switch to V8 online and let it update.

If you have any further questions, feel free to ask them here.


Stephan
machine-translated from German · Show original
Remo1984 22 March 2026 18:5622.03.2026 18:56
Perfect, thank you so much :-)
machine-translated from German · Show original
Eddi E. aus G. 23 March 2026 09:0123.03.2026 09:01
Good morning,

A little word of warning :-)

Make sure you know which firmware you are selecting before updating with the transmitter: Extender or RX2, for example, can only be re-updated using a computer; only binding-capable firmwares can be updated OTA (VBasic, VPlane, Heli, Pro, +Rescue).

But even with an M4 you're not left out (I'm sitting at one myself...): look .

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless