Hello everyone,
I'm completely new to the Vstabi/Vbar world and am currently setting up my first helicopter with it. The basic setup was very easy.
Now to my question: I have a 1st RC backup battery installed. It can be switched off by changing a servo signal from +100 to -100 on the channel it's connected to (e.g., Servo4 or AUX1). How can I configure the VBar so that any switch, or even better, a rotary knob, triggers this process?
I think I've already solved another problem: My YGE ESC isn't being recognized, even though I've installed and activated all the software (YGE software and Auto Install software). But I suspect that's because I previously had Graupner telemetry configured, and therefore the "Autodetect" for Mikado no longer works, correct?
Best regards,
Jan Riggert
Edited once. Last edited on 12/03/2026 at 06:26 by Jan_Privat.
I'm completely new to the Vstabi/Vbar world and am currently setting up my first helicopter with it. The basic setup was very easy.
Now to my question: I have a 1st RC backup battery installed. It can be switched off by changing a servo signal from +100 to -100 on the channel it's connected to (e.g., Servo4 or AUX1). How can I configure the VBar so that any switch, or even better, a rotary knob, triggers this process?
I think I've already solved another problem: My YGE ESC isn't being recognized, even though I've installed and activated all the software (YGE software and Auto Install software). But I suspect that's because I previously had Graupner telemetry configured, and therefore the "Autodetect" for Mikado no longer works, correct?
Best regards,
Jan Riggert
Edited once. Last edited on 12/03/2026 at 06:26 by Jan_Privat.
Hallo zusammen,
ich bin noch ganz neu in der Vstabi/Vbar Welt und richte gerade meinen ersten Heli damit ein. Das grundsätzliche Set-Up war auch sehr easy.
Jetzt aber zu meiner Frage: Ich habe einen 1st RC-Pufferakku verbaut. Den kann man ausschalten, wenn man an dem Kanal wo er angeschlossen ist (z.B. Servo4 oder AUX1) ein Servosignal von +100 auf -100 schaltet. Wie kann ich es in der VBar einrichten, dass ein beliebiger Schalter oder besser noch Drehregler diesen Vorgang schaltet?
Ein anderes Problem hab ich vermutlich schon gelöst: Mein YGE-Regler wird nicht erkannt, obwohl ich sämtliche Software installiert & aktiviert habe (YGE Software und Auto Install Software). Aber vermutlich liegt es daran, dass ich vorher Graupner Telemetrie eingestellt hatte und daher das "Autodetect" für Mikado nicht mehr funktioniert, korrekt?
Mit freundlichen Grüßen,
Jan Riggert
1 mal bearbeitet. Zuletzt am 12.03.2026 06:26 von Jan_Privat.
ich bin noch ganz neu in der Vstabi/Vbar Welt und richte gerade meinen ersten Heli damit ein. Das grundsätzliche Set-Up war auch sehr easy.
Jetzt aber zu meiner Frage: Ich habe einen 1st RC-Pufferakku verbaut. Den kann man ausschalten, wenn man an dem Kanal wo er angeschlossen ist (z.B. Servo4 oder AUX1) ein Servosignal von +100 auf -100 schaltet. Wie kann ich es in der VBar einrichten, dass ein beliebiger Schalter oder besser noch Drehregler diesen Vorgang schaltet?
Ein anderes Problem hab ich vermutlich schon gelöst: Mein YGE-Regler wird nicht erkannt, obwohl ich sämtliche Software installiert & aktiviert habe (YGE Software und Auto Install Software). Aber vermutlich liegt es daran, dass ich vorher Graupner Telemetrie eingestellt hatte und daher das "Autodetect" für Mikado nicht mehr funktioniert, korrekt?
Mit freundlichen Grüßen,
Jan Riggert
1 mal bearbeitet. Zuletzt am 12.03.2026 06:26 von Jan_Privat.
machine-translated from German · Show original