← VBar Control Touch / EVO

Bank switching not so abrupt translated

VBar Control › VBar Control Touch / EVO · Started by steveman on 3 February 2026 15:3703.02.2026 15:37
steveman 3 February 2026 15:3703.02.2026 15:37
A question:
Is there a setting somewhere to make the bank switching less abrupt? I'm concerned about the different RPMs, where the tail really wobbles when switching. It's not ideal in scale. (Yes, I do fly at different RPMs in my scale.)
I use the vbar controller in conjunction with Hobbywing.
Regards, Stefan
machine-translated from German · Show original
RV 3 February 2026 18:4603.02.2026 18:46
No, that's not adjustable and not currently feasible.

Parameter sets are switched between banks, meaning they have to be loaded into the workspace - and that is always "switching" not "fading".

When it comes to the RPMs, you can set the ramp to 2 and reduce the integral and sensitivity.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
steveman 3 February 2026 19:0003.02.2026 19:00
Okay. Then I'll go and look for the ramp.
Regards
machine-translated from German · Show original
steveman 3 February 2026 19:2303.02.2026 19:23
By Ramp 2, do you mean Bank 2?
And then reduce the value there from 20.
I'll test it next time I'm at the venue.
Thanks
machine-translated from German · Show original
RV 3 February 2026 20:2103.02.2026 20:21
Ramp is the acceleration limiter in the governor. It's normally set to 3. If you change it to 2, it will be slower during startup and transitions.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 03.02.2026 20:21 von RV.
machine-translated from German · Show original
steveman 3 February 2026 20:4403.02.2026 20:44
Thank you so much. Now I know what you mean.
I'll change that. Best regards, Stefan
machine-translated from German · Show original
JMalberg 3 February 2026 22:5403.02.2026 22:54
Hi you two,
(I've already written this in another Heliversum :-) )

I've always understood it to mean that, as with all these PID controllers, including the VGov, the output/motor speed is never directly controlled by the input alone:
The VGov receives a new target speed. Then, using its numerous parameters, it adjusts the engine speed to the new target speed, more or less quickly.
If there were a delay in the input, like in the old days, the VGov would simply be changing the speed incrementally for several seconds at a time, and would just have more work to do until the target speed was finally reached. That doesn't make sense anymore, in my opinion.

I didn't adjust much on the VGov for my helicopters, as the default values already gave me a good result.

What I can say, however, is that the VGov regulates noticeably better than my YGE controllers. With the VGov, I have to look very closely to see any tail movement; with the YGE, it's clearly visible.

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless