← VBar Control Touch / EVO

Vbar Control evo - Hobbywing platinum 130v4 translated

VBar Control › VBar Control Touch / EVO · Started by steveman on 25 January 2026 21:4225.01.2026 21:42
steveman 25 January 2026 21:4225.01.2026 21:42
Good evening. Up until now, I've been using my old Jives in a very old-fashioned way. But now I got the itch and equipped a Logo 600se with a Hobbywing Platinum 130A V4. I made a telemetry cable and connected it. The ESC is set to Fixed Wing (I hope that's correct) and the control is handled by the vstabi neo. The vbar software is installed on the ESC.
I installed and activated the Hobbywing app on the vbar Control evo. The app starts even when I connect a battery; the motor also starts, revs up, and displays the RPM on the remote control screen.

I thought I could now adjust all the controller settings via the remote. However, I can't change anything there. If I press and hold the hardware icon, I get to a settings page, but I can't change anything there.
Is this only possible with newer Hobbywing controllers, or have I done something wrong?

Best regards and thanks in advance for any help you can offer.
machine-translated from German · Show original
RV 25 January 2026 21:5325.01.2026 21:53
Please note the following:

- The controller must have the latest firmware for VBar Gov loaded.
- Don't do any of those old "sticky tweaks for mods"! - That's from the Stone Age.
- In the model setup, AFTER the controller is detected, scroll down and click Govtype, done.
- Now ONLY the direction of rotation and BEC voltage need to be set in the controller app.

If the controller is detected but the settings are unavailable, the causes are:
- wrong firmware installed
- The regulator can't

Background: HW uses a status bit to inform us which values are adjustable for each controller. If nothing is possible or the value is grayed out, the information is either not received or not being sent. In either case, please contact HW.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
steveman 25 January 2026 22:0725.01.2026 22:07
Thank you for the feedback.
I updated the controller yesterday, so it should be the latest version. I'll take another look at it though.
Regards, Stefan
machine-translated from German · Show original
Eddi E. aus G. 26 January 2026 09:3226.01.2026 09:32
Hi Stefan,

And... perhaps a little patience. The app only grays out the available/possible settings once the controller has 'burped up' all status bits via the telemetry channel :-) to prevent you from messing around with something that isn't working yet or at all.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
steveman 26 January 2026 15:5226.01.2026 15:52
OK thanks.
I've checked everything again. I've verified the software; it's up to date.
The strange thing is that the Hobbywing app thinks it's a Platinum 150A LV.
My controller is a 130a Hv v4.

Perhaps things will change over time. For now, I'm going flying. I can program the controller with the Progbox anyway.
Regards



machine-translated from German · Show original
steveman 26 January 2026 18:0626.01.2026 18:06
The problem was an old Hobbywing USB Link software. I installed the new one, and then a newer firmware was offered for my controller, and with that, everything works as it should.
Regards, Stefan
machine-translated from German · Show original
Eddi E. aus G. 27 January 2026 09:0327.01.2026 09:03
:-)

Which version is this (USB Link Software)?

I get asked about the connection issue every now and then, and I can usually only refer people to hardware support.
That would help me :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Teci 27 January 2026 09:5827.01.2026 09:58
Good morning
Currently, it's USB Link V5.1.0
https://www.hobbywing.com/en/service/application?id=1

LG
machine-translated from German · Show original
steveman 27 January 2026 20:5827.01.2026 20:58
Just like Teci wrote.
Regards
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless