Racerbuk
15 January 2026 18:0515.01.2026 18:05
Hello everyone,
I wanted to adjust my 3-blade rotor head today. Mechanically, I've managed to get the rear blade to only move minimally when I apply pitch. Now I want to fine-tune it virtually in Vbar Touch, but I can't find the Expert virtual swashplate adjustment mode. The VBar is the standard version, not the Pro or Rescue mode.
Perhaps the mechanical adjustment is sufficient, as I said the rear blade only moves marginally, but I still want to try the virtual twisting.
Where can I find them?
Greetings Günter
Hallo Zusammen,
ich wollte heute meinen 3-Blatt Rotorkopf einstellen. Mechanisch hat es so weit geklappt, dass sich das hintere Blatt nur noch marginal bewegt wenn man Nick gibt. Jetzt wollte ich es noch in der Vbar Touch virtuell noch perfektionieren, finde jedoch den Einstellmodus Expert virtuelle Taumelscheibenverdrehung nicht. Das VStabi ist das Normale, also kein Pro oder Rettung.
Eventuell reicht ja die mechanische Einstellung soweit schon, wie gesagt bewegt sich das hintere Blatt nur marginal , möchte aber trotzdem den Versuch starten mit der virtuellen Verdrehung.
Wo finde ich die ?
Grüße Günter
RV
15 January 2026 20:1115.01.2026 20:11
You need at least the Pro version for that.
I would never mechanically twist anything as much as may have been done here. Please remember that from a kinematic point of view, it's best if the control linkages always run vertically (zero pitch) downwards to the swashplate.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Du brauchst dazu Pro mindestens.
Ich würde auch immer nichts mechanisch so weit verdrehen wie ggf. hier jetzt gemacht wurde. Bitte bedenke dass es von der Kinematik am Besten ist wenn die Anlenkgestänge immer senkrecht (Nullpitchlage) zur TS nach unten gehen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Racerbuk
15 January 2026 20:2515.01.2026 20:25
Okay, then I'll have to buy the Pro version. The linkages are only slightly angled forward; I thought that's how it used to be done. It's annoying because the stabilizer bar has to come out again for the update.
Ok, dann muss ich das Pro dazukaufen. Die Gestänge stehen nur ganz leicht nach vorne, hab gedacht das hat man ja früher auch so gemacht. Ist halt blöd weil das Stabi wieder raus muss fürs update.
RV
15 January 2026 20:3315.01.2026 20:33
The stabilizer can be updated wirelessly using a VBar Control touch or EVO.
https://www.vstabi.info/de/node/2279
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Die Stabi kann man mit einer VBar Control touch oder EVO über die Funkstrecke updaten.
https://www.vstabi.info/de/node/2279
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
JMalberg
15 January 2026 20:3615.01.2026 20:36
Good morning,
The VBAR doesn't need to be removed at all. That's precisely one of the advantages of VBAR NEO: all updates are done via OTA.
Buy the update, enable VBC and VBAR, start the OTA update, a quick hello to the best woman in the world... Ta-da! VBAR is ready.
When I think back to the old days…
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Moin,
Das VBAR muss überhaupt nicht ausgebaut werden. Das ist ja gerade einer der Vorteile ab VBAR NEO, das jeglicher Update per OTA läuft.
Update kaufen, VBC und VBAR anschalten, OTA starten, kurz ein Hallo zur besten Frau der Welt …. Tada! VBAR fertig.
Wenn ich da an die alten Zeiten denke….
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
Racerbuk
15 January 2026 21:0015.01.2026 21:00
Okay then, I'll give it a go tomorrow.
Regards, Günter
Na dann, werde ich morgen mal angreifen
Gruss Günter
Racerbuk
16 January 2026 12:3916.01.2026 12:39
Hello Rainer
Everything is set up correctly and works. However, if I adjust it so that the blade above the tail boom doesn't move during pitch, then the left blade (in the direction of flight) moves during roll, which shouldn't happen with a 3-blade propeller, right? The setting is H2, the helicopter is a Hirobo Lama, and all servos are in the front.
Greetings Günter
Hallo Rainer
Alles so gemacht und funktioniert. Allerdings wenn ich das so einstelle dass sich das Blatt über dem Heckrohr nicht mehr bewegt bei Nick, dann bewegt sich bei Roll allerdings das in Flugrichtung linke Blatt, was es beim 3Blatt doch nicht sollte , oder ? Eingestellt ist H2, der Heli ist ein Hirobo Lama und alle Servos sind vorne.
Grüsse Günter
Racerbuk
16 January 2026 12:4016.01.2026 12:40
Here's a photo
Hier mal ein Foto
Racerbuk
16 January 2026 12:4716.01.2026 12:47
That's the correct setup. The linkage must be perfectly perpendicular.
So ist die Einstellung. Gestänge exakt rechtwinklig
Racerbuk
16 January 2026 12:4816.01.2026 12:48
That's how the twist is set. Perhaps the wrong mode is selected with H2? Pitch, nimble, and roll work fine like that on the workbench. However, at full pitch, the head rotates very slowly.
Edited once. Last edited on 16.01.2026 at 13:03 by Racerbuk.
So ist die Verdrehung eingestellt. Eventl ist ja auch der falsche Modus mit H2 eingestellt? Pitch Nick Roll funktioniert so jedenfalls am Bautisch. Allerdings bei voll Nick dreht sich der Kopf nur seh gebremst
1 mal bearbeitet. Zuletzt am 16.01.2026 13:03 von Racerbuk.
Eddi E. aus G.
16 January 2026 13:0516.01.2026 13:05
Good morning.
Leading by 90° means that the control impulse comes 90° before the time the leaf passes by.
With a 2-blade propeller, the blades either don't move along the longitudinal axis when you control pitch, or they move when you control roll.
The same applies to the 3-blade rotor, except that at the same time no blade is moving 90° forward on roll, but rather beyond it... meaning it naturally receives a portion of the control impulse, for which it is then practically responsible 90° later.
If one leaf is positioned exactly sideways, it won't move, but the other two will, since they are also not, or still not, at a right angle.
And if the object in question moves even a tiny bit, it doesn't matter... the actual static lead is somewhere else anyway, and it also twists dynamically depending on the flight condition.
You can then fly it, hotstart Nick and Pitch, see where the model pulls on Roll at the same time, or make a sharp upward turn from straight flight with Nick, as well.
Then simply turn it (5° increments are sufficient to start with) until the effect is minimal.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin.
90° vorlaufend bedeutet ja, dass der Steuerimpuls eben 90° vor der Zeit kommt, wo das Blatt vorbeikommt.
Beim 2-Blatt bewegen sich eben die Blätter auf der Längsachse nicht, wenn man Nick steuert, oder sie bewegen sich, wenn man Roll steuert.
Beim 3-Blatt gilt das selbe, nur dass gleichzeitig ja kein Blatt 90° vorlaufend auf Roll steht, sondern drüber raus ... d. h. es bekommt natürlich den Steuerimpuls anteilig mit, für den es dann eben 90° später quasi-praktisch zuständig ist.
Wenn ein Blatt exakt quer steht, bewegt sich das nicht, dafür die beiden anderen, die ja auch nicht oder immer noch nicht im rechten Winkel stehen.
Und wenn sich das betreffende trotzdem ein Mü bewegt, ist es wumpe ... der tatsächliche statische Vorlauf liegt sowieso woanders, und dynamisch je nach Flugzustand verdreht der sich auch noch.
Das kann man dann erfliegen, Hotstart Nick und Pitch, schauen, wohin das Modell gleichzeitig auf Roll zieht, oder aus dem Geradeausflug mit Nick einen Haken nach oben schlagen, ebenso.
Dann einfach so lange dran drehen (5°-Schritte reichen erst mal), bis der Effekt am geringsten ist.
Grüßle
Eddi
Born to fly ...
forced to work.
Racerbuk
16 January 2026 13:1216.01.2026 13:12
Hello Eddie
Thanks in advance for the info. The linkages are perfectly aligned, which is very important, I think. Regarding mode H2, is that okay?
Hallo Eddi
Danke schon mal f.d. Info. Die Gestänge sind ja exakt ausgerichtet, ist ja auch sehr wichtig, denke ich. Bezgl. des Modus H2 ist so ok oder?
Eddi E. aus G.
16 January 2026 13:3816.01.2026 13:38
Hey,
Being precise is good, but since the whole thing is constantly in motion during flight and also reacts to dynamic influences, which the VBar can control perfectly, I think good enough is good enough :-)
You can really measure yourself to death, and possibly measure something different every other time... nah, I'm past that age ^^ (or not (yet) back in it...).
Regarding the linkage (initially independent of what happens above the TS at the blade holders):
If in doubt, please adjust the swashplate again as for a 2-blade propeller, i.e., without twisting, so that it moves neutrally around the axis in pitch and roll.
Then use the rotate ( << ) ( >> ) arrows until it fits the 3-leaf.
Grüßle
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 16.01.2026 13:40 von Eddi E. aus G..
Hej,
exakt ist schon gut, aber da das ganze im Flug später sowieso ständig in Bewegung ist und auch auf dynamische Einflüsse reagiert, was die VStabi super aussteuern kann, halte ich gut genug für gut genug :-)
Man kann sich wirklich einen Wolf messen, und misst womöglich jedes 2. Mal was anderes, ... näh, aus dem Alter bin ich raus ^^ (oder noch nicht (wieder) drin ...).
Zur Anlenkung (zunächst unabhängig von dem, was über der TS an den Blatthaltern passiert):
Stelle die Taumelscheibe im Zweifel bitte nochmal so ein, wie für einen 2-Blatt, d. h. ohne Verdrehung, so dass sie sich achsneutral auf Nick und Roll bewegt.
Dann verwenden die Drehen ( << ) ( >> ) Pfeile, bis es für den 3-Blatt passt.
Grüßle
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 16.01.2026 13:40 von Eddi E. aus G..
Racerbuk
16 January 2026 14:3216.01.2026 14:32
Okay. Thanks in advance.
Ok. Danke schon mal
JMalberg
16 January 2026 15:0816.01.2026 15:08
@racerbuk:
Using the highly accurate protractor-on-the-monitor method, I would also say that the TS rotation is approximately 56-62°. That seems about right.
But to be pedantic... :-)
The TS driver is freely rotatable on the HaRo shaft (?)
As far as I can tell from the top view, the center of the ball of the blade linkage is not exactly on the same plane as the longitudinal axis of the HaRo shaft, like the TS ball.
If you now turn the drive pin 6-11° clockwise, the linkages will run more precisely on the aforementioned plane and no longer at an angle. The VBAR algorithm will be happy about that :-)
The virtual TS rotation is not changed as a result.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Edited twice. Last edited on 16.01.2026 at 15:09 by JMalberg.
@racerbuk:
Nach der hochgenauen Geodreick-auf-dem-Monitor-Methode würde ich auch sagen, dass die TS-Verdrehung ca 56-62° ist. Das passt scho
Aber um pedantisch zu sein... :-)
Der TS-Mitnehmer ist frei drehbar auf der HaRo-Welle (?)
Soweit ich es auf der Draufsicht erkennen kann, ist der Kugelmittelpunkt der Blattanlenkung nicht genau auf der zur HaRo-Welle-Längsachse-Ebene wie die TS-Kugel.
Wennste jetzt die den Mitnehmer 6-11° im Uhrzeigersinn drehst, laufen die Gestänge genauer auf der o.g. Ebene und nicht mehr schief. Da freut sich der Algorithmus des VBAR :-)
Die virtuelle TS-Verdrehung wird dadurch nicht verändert.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
2 mal bearbeitet. Zuletzt am 16.01.2026 15:09 von JMalberg.
Racerbuk
16 January 2026 15:3916.01.2026 15:39
Hi Jürgen, now I see it too. Thanks :-)
Hallo Jürgen, jetuz seh ichs auch. Danke :-)
Racerbuk
17 January 2026 06:4517.01.2026 06:45
Brief information
Everything worked out. Jürgen's tip did the trick. The swashplate was indeed misaligned; there was a kink in the optical system. I then aligned it parallel to the main rotor shaft, and I was able to reduce the virtual swashplate twist considerably. Now the (unflown) characteristics are correct, and the rotor head is doing exactly what it's supposed to. The rest will be revealed in the flight test.
Thanks to everyone and best regards, Günter
Kurze Info
Hat alles geklappt. Der Tip von Jürgen hats gebracht. Die Taumel war wirklich negativ gestanden, hatte da einen Knick in der Optik. Hab diese dann parallel zur Hauptrotorwelle ausgerichtet und die virtuelle Taumelscheibenverdrehung konnte ich einiges zurücknehmen. Jetzt passen die ( ungeflogenen) Eigenschaften und der Kopf macht genau was er soll. Den Rest wird der Flugtest zeigen.
Danke an Alle und viele Grüsse Günter