Rolf Rakette
3 November 2025 18:4103.11.2025 18:41
Good evening,
This module also appears to be new.
Where is this used, or what does it do when it's installed?
Greetings
Rolf
Nabend,
diese Modul ist auch neu wie mir scheint.
Wo nutzt man das bzw was macht das wenn man diese Einbaut?
Grüße
Rolf
RV
3 November 2025 18:4703.11.2025 18:47
There are areas in this world that are not subject to CE guidelines.
Although the radio power is always sufficient with CE compliant operating mode, there may be situations (especially when other pilots are flying at the same place with FCC modules at the same time) where it is good to have a little more power.
Personally, I would like to see the dynamic mode become a kind of "global default" for all transmitters (please, this is pure fantasy!) – because then you only ever get the power that's actually needed. Even well below CE in close range, which is usually sufficient.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Es gibt Gegenden in dieser Welt welche nicht den CE Richtlinien unterliegen.
Obwohl die Funkleistung mit CE konformer Betriebsart immer ausreicht kann es doch Situationen geben (insbesondere wenn andere Piloten am selben Platz mit FCC-Modulen gleichzeitig fliegen) wo es gut ist etwas mehr Power zu haben.
Ich persönlich würde mir wünschen dass der dynamische Modus eine art "weltweite Vorgabe" wird für alle Sender (Bitte jetzt - reine Phantasie!) - denn hier hat man immer nur die Leistung anliegen welche gerade benötigt wird. Auch deutlich unter CE im Nahbereich was meist ausreicht.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Rolf Rakette
3 November 2025 18:5903.11.2025 18:59
Ah, so that's how it is; it's not really meant for here.
Or rather, you could install it, but better not get caught. :-)
I like the idea of reducing the volume at close range.
Couldn't something be done that's legal?
I'm thinking about the distance when plugging in the battery because there are sometimes problems with that.
Or must the transmission power always be constant according to the law?
Greetings
Ah so ist das, also eigentlich nicht für hier gedacht.
Bzw könnte man schon einbauen aber besser nicht erwischen lassen. :-)
Die Idee mit dem Runterregeln im Nahbereich gefällt mir.
Könnte man da nicht wirklich was machen was Legal ist?
Ich denke da an die Entfernung beim anstecken des Akkus weil es da ab und an was Probleme gibt.
Oder muss die Sendeleistung immer konstant sein laut Gesetz?
Grüße
RV
3 November 2025 20:0603.11.2025 20:06
Quote: I'm thinking about the distance when plugging in the battery because there are sometimes problems with that.
What results in the connection is the feedback from the stabilizer (!!!) - and this is not power-controlled, which is why it can sometimes "shout" at the receiver part in the VBC in certain proximity/orientation.
As soon as the connection is established and we have performance data about the reception at the stabilizer in the VBC, then the "N" (near field) setting will also activate. But ONLY for the direction from the VBC to the stabilizer.
For safety reasons, this procedure cannot be changed; otherwise, a packet loss in flight with failsafe would always be fatal, as a reconnect might not occur due to "limited speed." This way, we always have a chance of reconnecting.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 03.11.2025 20:09 von RV.
Quote:Ich denke da an die Entfernung beim anstecken des Akkus weil es da ab und an was Probleme gibt.
Was den Connect ergibt ist die RÜCKmeldung vom Stabi (!!!) - und die ist nicht Leistungsgesteuert, deswegen kann das in bestimmter Nähe/Ausrichtung den Empfängerteil in der VBC mal "zuschreien".
Sowie der Connect da ist und uns Leistungsdaten über den Empfang an der Stabi in der VBC vorliegen - geht doch dann auch das "N" (Nahfeld) an. Aber NUR für die Richtung VBC zu Stabi.
Aus Sicherheitsgründen kann man an diesem Verfahren nichts ändern, sonst wäre ein Paketverlust im Flug mit Failsafe immer tödlich, es käme dann ggf. kein Reconnect zustande da "gebremster Schaum". So haben wir immer die Chance auf einen Reconnect.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 03.11.2025 20:09 von RV.
Eddi E. aus G.
4 November 2025 09:1404.11.2025 09:14
Good morning,
The transmission power is defined as a maximum; theoretically, anything below that is always possible.
The new module has adjustable CE, two types of FCC, dynamic as needed (max. 1 W but essentially the adaptive energy saving mode) and full power (1 W).
In Europe, you can only legally use CE-compliant devices, in the USA FCC-compliant ones, but many regions outside the EU also follow CE or FCC standards (probably because it's simpler...), and where nobody cares or if you have a corresponding radio license, you can use even more; you have to find out for yourself in the region (if you want to stay legal).
The annoying thing, especially in 'other regions' but possibly also here, is that everyone does as they please, and in the worst case, this 'smooths over' the honest ones (e.g., CE 100 mW EIRP, LBT) (and even boasts about it...).
To make a long story short: it wouldn't make any difference here whether you use the original device or the MRM in CE mode. And interestingly, experience shows that the EU also has the fewest problems with range and packet loss, perhaps partly because the density isn't as high, and partly because the regulations make perfect sense for everyone involved.
In more 'anarchic' regions, or where the regulations allow more freedom, it's more likely... and that's precisely what the module is designed for.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
die Sendeleistung ist im Maximum definiert, drunter geht theoretisch immer.
Das neue Modul hat einstellbar CE, zweierlei FCC, dynamisch nach Bedarf (max. 1 W aber quasi der adaptive Energiesparmodus) und volle Lotte (1 W).
In Europa darf man legal nur CE-konforme Geräte verwenden, in den USA FCC-konforme, viele Regionen außerhalb der EU orientieren sich aber auch an CE oder FCC (wohl weil's einfacher ist ...), und wo's keinen kratzt oder wenn man bspw. eine entsprechende Funklizenz hat auch mehr, das muss man (wenn man legal bleiben will) entsprechend der Region herausfinden.
Das blöde speziell in 'anderen Regionen' aber ggfs. auch hier ist, dass jeder macht wie er will, und damit die ehrlichen (bspw. CE 100 mW EIRP, LBT) schlimmstenfalls 'wegbügelt' (und sich noch damit brüstet ...).
Kurzer Rede langer Unsinn: hier würde es keinen Unterschied machen, das originale oder das MRM im CE-Modus. Und interessanterweise gibt es in der EU erfahrungsgemäß auch die wenigsten Probleme mit Reichweite, Paketverlusten, einmal vielleicht weil die Dichte nicht so hoch ist, und weil die Regelungen durchaus Sinn ergeben, für alle Beteiligten.
In 'anarchischeren' Regionen, oder wo die Regelungen eben auch mehr zulassen, eher ... und dafür ist das Modul eben gedacht, gemacht.
Grüßle
Eddi
Born to fly ...
forced to work.
thomas1130
12 March 2026 14:3812.03.2026 14:38
A quick question for clarification:
Unlike CE 100 mW EIRP, the "Dynamic Mode" can also transmit below 100 mW - so it is no longer "necessary"?
Does it continuously and "quickly" adjust the performance during operation to the reception situation?
...while the EU version ALWAYS uses 100mW??
Are there differences in the "frequency jumps" - or in LBT - between CE and Dynamic mode?
Thanks!
Best regards,
Thomas
(73)
Edited twice. Last edited on 12/03/2026 at 15:05 by thomas1130.
Kurze Frage zum Verständnis:
Der "Dynamik Mode" kann im Gegensatz zu CE 100 mW EIRP auch unter 100mW senden - so nicht mehr "notwendig" ist?
Er passt die Leistung im Betrieb laufend und "schnell" an die Empfangssituation an?
... während die EU Variante IMMER die 100mW verwendet??
Gibt es Unterschiede bei den "Frequenzsprüngen" - bzw bei LBT - zwischen dem CE und dem Dyamik-Mode?
Danke!
LG,
Thomas
(73)
2 mal bearbeitet. Zuletzt am 12.03.2026 15:05 von thomas1130.
RV
12 March 2026 16:3912.03.2026 16:39
Regarding point 1: yep, that's right!
Regarding point 2: AFAIK, no.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Zu 1: jupp, so ist es!
Zu 2: AFAIK nein.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
thomas1130
12 March 2026 19:4712.03.2026 19:47
ulrich
13 March 2026 10:1913.03.2026 10:19
Additional information about LBT:
Our VLink is very efficient in its bandwidth usage, so an LBT event has only a minimal impact on the transmit power. We only need to reduce it by a few dB to stay below the required 10% media usage. As a result, our system barely interferes with other users and is therefore cooperative. This remains true even at transmit powers higher than 100mW EIRP (non-CE). Since dynamic transmission almost always uses less than 100mW, there is practically no discernible difference with or without LBT.
So long... Uli
http://www.vstabi.de Edited once. Last edited on 13.03.2026 at 10:22 by ulrich.
Eine Zusatzinfo zu LBT:
Unser VLink ist sehr sparsam in der Bandnutzung, so dass ein LBT Ereignis eine nur sehr geringe Auswirkung auf die Sendeleistung hat. Wir müssen nur wenige dB reduzieren um unter der geforderten 10% Media Usage zu bleiben. Dadurch stört unser System andere Nutzer nur wenig, ist also kooperativ. Das bleibt auch bei höherer Sendeleistung als 100mW EIRP so (non CE). Da dynamic fast immer weniger als 100mW sendet, ist also mit/ohne LBT praktisch kein Unterschied mehr erkennbar.
so long ... Uli
http://www.vstabi.de
1 mal bearbeitet. Zuletzt am 13.03.2026 10:22 von ulrich.
thomas1130
13 March 2026 11:4013.03.2026 11:40
Great - THANK YOU Uli for the technical insight :-)
Now I know what I wanted to know :-)
vy73
Best regards,
Thomas
Edited once. Last edited on 13.03.2026 at 11:41 by thomas1130.
Super - DANKE Uli für den technischen Insight :-)
Damit weiß ich was ich wissen wollte :-)
vy73
LG,
Thomas
1 mal bearbeitet. Zuletzt am 13.03.2026 11:41 von thomas1130.