Eddi E. from G. wrote:
-------------------------------------------------------
> Hi,
>
Not that I know of.
>
> When switched on, the stick centers are
> trained (therefore: all sticks to center and in
(> Silence, pitch is of course irrelevant).
> If the expected center is not where we find it
> expect, or if the potentiometer doesn't come to rest,
An error message appears because we...
> may already suspect that something is going on
> is not true, and because it is dangerous in flight
> could become. Then, for example, a warning; Abnormal
> Resting value of the Nick RC channel.
> If the initialization process succeeds, the changes will be made
> the stick positions are then expressed as rotation rates
Understood – makes sense. The more sticks, the
> faster to the end of physics.
> On the ground, the TS may then run into the
> electronic limiter (model moves)
> No, VBar 'gives it its all', but it happens
> nothing).
>
> With a third-party broadcaster, it would be like this if in
> possibly only one in another flight phase
Minimal trim would be one thing
> Tax input (deviation from the center, where from)
> Should the VBar know where this comes from ..?),
The TS would run away on the ground, or the model
> drifting in flight.
> Similarly, if servo positions are specified in the receiver
> would be stored (fail-safe) and as long as
> would be issued until the sender and the
> Receivers have connected, and from the sender
> then differing positions would emerge.
VBar Control doesn't have that.
Unless... one or more potentiometers were malfunctioning,
> the center would still change after the initialization
> change.
Hence the question about calibration, and my
> Addendum: Will it remain calm then? Possibly also.
> Thinking further, what would happen if one were from the
Does heat go into cold or vice versa?
>
The message comes from VBar, which also does
> If it's version 4.0 or older, just write it in the...
Log. VBar Control has direct access, solves the
> but not out, neither the classic nor the
> Touch.
>
If it's the same for all NEOs, and if it's the same for the
If the stick is pointing in that direction, it will be the transmitter.
> (logical deduction).
The only question now is, why?
Stick calibration clearly 'off' -> new
Doing it won't hurt either way.
Temperature effect -> very unusual, we
They can fly at any temperature, but in
> Doubts, compare, inside, outside (sender)
(Let it cool down beforehand), from inside to outside,
> Transmitter switched on and allowed to cool down.
>
> . Spring tension -> if it is very low, the
> The stick should move very slightly around the center
> does not allow sufficient movement from the spring into the
> center can be drawn
> . Movement when switching on -> simply try the transmitter
> leave lying down while tying
> Faulty potentiometer -> very unusual, simple,
> because we have practically no potentiometer problems so far
> could/were allowed/had to record -> if the
The effect is repeatable and, for example, always occurs on one
> Channel, a potentiometer shows, at times the
> Switch to stick mode, see if it goes away then
> or moves with the stick (e.g., rear end ...
> Roll), with Nick ... Pitch rather error occurs,
> Error does not occur
>
That's all for now :-)
>
> Greetings
>
> Eddie
Hello everyone, I'm the "new guy" who has already made his beginner mistakes with Heli Babys and the Cobra from Schlütter.
As a newcomer after a long break, I can solve the problems I don't understand by reading. Thank you all for that. Greetings, Ferdinand
Eddi E. aus G. schrieb:
-------------------------------------------------------
> Moin,
>
> nicht das ich wüsste.
>
> Beim Einschalten werden die Knüppelmitten
> eingelernt (daher: alle Knüppel auf Mitte und in
> Ruhe, Pitch ist natürlich egal).
> Wenn die erwartete Mitte nicht ist wo wir sie
> erwarten, oder wenn das Poti nicht zur Ruhe kommt,
> kommt eine Fehlermeldung, weil wir im Vorhinein
> schon den Verdacht haben können, dass da was
> nicht stimmt, und weil es im Flug gefährlich
> werden könnte. Dann bspw. Warn;Abnormaler
> Ruhewert des Nick RC Kanals.
> Wenn der Init durchgeht, werden die Veränderung
> der Knüppelstellungen danach eben als Drehraten
> verstanden – logisch. Je mehr Knüppel, je
> schneller bis zum Ende der Physik.
> Am Boden läuft die TS dann u. U. in den
> elektronischen Begrenzer (Modell bewegt sich
> nicht, VStabi 'gibt alles', es passiert aber
> nix).
>
> Bei einem Fremdsender wäre es jetzt so, wenn in
> einer anderen Flugphase womöglich auch nur ein
> minimaler Trimm wäre, wäre das eine
> Steuer-Eingabe (Abweichung von der Mitte, woher
> soll's die VStabi wissen, woher das kommt ..?),
> die TS würde am Boden weglaufen, oder das Modell
> im Flug driften.
> Genauso, wenn im Empfänger Servopositionen
> gespeichert wären (Fail-Safe) und so lange
> ausgegeben würden, bis der Sender und der
> Empfänger sich verbunden haben, und vom Sender
> dann abweichende Positionen kommen würden.
> Bei VBar Control gibt's das nicht.
> Außer ... ein oder mehrere Potis wären unruhig,
> die Mitte würde sich nach dem Init noch
> verändern.
> Daher die Frage nah er Kalibrierung, und meine
> Ergänzung, bleibt die dann auch ruhig? Ggfs. noch
> weiter gedacht, wie sieht es aus, wenn man aus der
> Wärme in die Kälte geht oder umgekehrt?
>
> Die Meldung kommt von der VStabi, das macht auch
> schon eine 4.0 oder älter, schreibt's halt in's
> Log. VBar Control hat direkten Zugriff, löst das
> aber nicht aus, weder die klassische noch die
> Touch.
>
> Wenn's bei allen NEOs so ist, und wenn's auf den
> Knüppel hindeutet, wird's der Sender sein
> (logischer Rückschluss).
> Die Frage ist nun nur, warum?
> . Knüppel-Kalibrierung deutlich 'off' -> neu
> machen, schadet so oder so nicht
> . Temperatur-Effekt -> sehr ungewöhnlich, wir
> fliegen ja selbst bei jeder Temperatur, aber im
> Zweifel mal vergleichen, drin, draußen (Sender
> vorher auskühlen lassen), von drin nach draußen,
> Sender eingeschaltet und gebunden auskühlen
> lassen
> . Federspannung -> wenn die sehr gering ist, der
> Knüppel sich um die Mitte ganz leicht bewegen
> lässt bzw. von der Feder nicht ausreichend in die
> Mitte gezogen werden kann
> . Bewegung beim Einschalten -> Sender einfach mal
> liegen lassen beim Binden
> . schadhaftes Poti -> sehr ungewöhnlich, einfach,
> weil wir bisher praktisch keine Poti-Probleme
> verzeichnen konnten-durften-mussten -> wenn der
> Effekt wiederholbar ist und bspw. immer auf einen
> Kanal, ein Poti zeigt, zeitweise mal den
> Stick-Mode umstellen, schauen, ob's dann weg ist
> oder mit dem Knüppel wandert (bspw. Heck ...
> Roll), bei Nick ... Pitch eher Fehler kommt,
> Fehler kommt nicht
>
> Soweit mal :-)
>
> Grüßle
>
> Eddi
Hallo zusammen, ich bin der "Neue" der schon mit Heli Babys und der Cobra von Schlütter seine Anfängerfehler gemacht hat.
Als Neueinsteiger nach längerer Pause kann ich, die Probleme die ich nicht verstehe, Lösen durch Lesen. Danke euch allen dafür. Grüsse Ferdinand