thomas1130
25 June 2026 16:5725.06.2026 16:57
Hi everyone,
I have a small "headspeed problem" with my Stratos:
The settings in the VBC EVO+ would be approximately 3800 / 4500 / 5200.
However, it feels quite (too?) "tame" for a 4s battery - and the log also shows headspeeds significantly below my values - in bank 3, for example, only 4390!?
Everything up to date - hardware controller update done - EVO also updated - and a new setup done again with the Stratos-200 preset?
Where is the mistake?
Thanks!
Best regards,
Thomas
Edited 2 time(s). Last edit at 06/25/2026 05:01PM by thomas1130.
Hi allerseits,
ich habe ein kleines "Headspeed-Problem" mit meinem Stratos:
Eingestellt in der VBC EVO+ wären ca 3800 / 4500 /5200
Er fliegt aber gefühlt recht (zu?) "zahm" für 4s - und das Log zeigt auch Headspeeds deutlich unter meinen Werten - in Bank 3 zB nur 4390!?
Alles am neuesten Stand - HW-Reglerupdate gemacht - EVO ebenfalls upgedatet - und nochmals neues Setup mit dem Stratos-200 Preset gemacht?
Wo liegt da der Fehler?
Danke!
LG,
Thomas
Edited 2 time(s). Last edit at 06/25/2026 05:01PM by thomas1130.
RV
25 June 2026 17:3925.06.2026 17:39
RPM range in VGov incorrectly set (max 4800) - check the transmission...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/25/2026 05:40PM by RV.
RPM Range im VGov falsch gesetzt (max 4800) - schau mal beim Getriebe ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/25/2026 05:40PM by RV.
thomas1130
25 June 2026 17:5125.06.2026 17:51
Thanks Rainer - I just applied the preset... - I'll check the value right away!
LG
Danke Rainer - ich hab einfach das Preset raufgebügelt.. - ich werde den Wert gleich kontrollieren!
LG
RV
25 June 2026 17:5325.06.2026 17:53
And don't forget to readjust the RPMs afterwards.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Und danach die RPMS nochmals nachstellen nicht vergessen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
thomas1130
25 June 2026 18:0325.06.2026 18:03
RPMs? :-)
RPM -> :-)
RPMS -> ?
Edited 1 time(s). Last edit at 06/25/2026 06:22PM by thomas1130.
RPMS ? :-)
RPM -> :-)
RPMS -> ?
Edited 1 time(s). Last edit at 06/25/2026 06:22PM by thomas1130.
RV
25 June 2026 18:2225.06.2026 18:22
Quote: 3800 / 4500 / 5200
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Quote:3800 / 4500 /5200
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
thomas1130
25 June 2026 18:2325.06.2026 18:23
:-)
Thanks :-)
Greetings from hot Vienna :-)
:-)
THX :-)
LG aus dem heißen Wien :-)
thomas1130
25 June 2026 20:2025.06.2026 20:20
RV Wrote:
-------------------------------------------------------
> RPM range in VGov incorrectly set (max 4800) -
> Check the gearbox...
Hmm... but if I set the maximum to 4800, then the maximum selectable speed is also 4800!?
Shouldn't such a small engine be able to turn 5200 rpm?
14400 is probably too much - what about 9600??
And one more thing - 12 pole pairs - is that correct?
LG
Thomas
Edited 1 time(s). Last edit at 06/25/2026 08:20PM by thomas1130.
RV Wrote:
-------------------------------------------------------
> RPM Range im VGov falsch gesetzt (max 4800) -
> schau mal beim Getriebe ...
Hmm.. aber wenn ich max 4800 setze, dann ist die maximale auswählbare Drehzahl auch 4800 !?
Eigentlich sollte ja so ein Zwerg auch 5200 drehen können??
14400 ist wohl zu viel - und wie sieht es mit 9600 aus??
Und noch was - 12 Polpaare - ist das korrekt?
LG
Thomas
Edited 1 time(s). Last edit at 06/25/2026 08:20PM by thomas1130.
RV
25 June 2026 20:2925.06.2026 20:29
Yep - that's what I meant. Set it to 9600 and then you need to adjust the 3 RPM. Leave the rest as is.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Jupp - das meinte ich. 9600 setzen und die 3 RPM muss man dann nachstellen. rest lassen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G.
26 June 2026 09:4526.06.2026 09:45
Good morning,
I don't have one, but where is the (thinking) error?
The preset contains 14,400, and also 3,780-4,500-5,220, which should work according to my understanding, not be clipped?
Otherwise ... :-)
Acronym Definition
RPMS Rapid Prototyping Mission Simulator
RPMS Raymore Peculiar Middle School
RPMS Regional Pest Management Strategy
RPMS Remote Power Management System
RPMS Rep Profit Management System
RPMS Resource and Patient Management System
RPMS Rosa Parks Middle School
RPMS Rarely Purchased Management System
Rock-Paper-(M?)-Scissors ^^
—Eddi
Born to fly ...
forced to work.
Moin,
hab kein', aber wo liegt der (Denk-)Fehler?
Im Preset sind 14.400 drin, und eben 3.780-4.500-5.220, sollte meinem Verständnis nach doch funktionieren, nicht gekappt?
Sonst ... :-)
Akronym Definition
RPMS Rapid-Prototyping Mission Simulator
RPMS Raymore Peculiar Mittelschule
RPMS Regionale Pest-Management-Strategie
RPMS Remote Power Managementsystem
RPMS Rep-Profit-Management-System
RPMS Ressourcen- und Patienten-Management-System
RPMS Rosa Parks-Mittelschule
RPMS Selten gekauft-Management-System
Rock-Paper-(M?)-Scissors ^^
—Eddi
Born to fly ...
forced to work.
thomas1130
26 June 2026 09:5826.06.2026 09:58
Eddi E. from G. wrote:
-------------------------------------------------------
> Hi,
>
> I don't have one, but where is the (thinking) error?
>
The preset contains 14,400, and that's it.
> 3,780-4,500-5,220, according to my understanding
> But they still work, not cut off?
>
Yes, exactly - that's how it is in the preset on the VBC - unfortunately, in reality, the thing spins noticeably less - across all banks...
This is also evident from the extremely low PWM openings of 49% and so on – that it "could do more" – especially on 4s..
Tried it today with 9600 -> exactly the same result - the set RPM and the log RPM (which seems correct based on gut feeling) don't match...
I could of course just set it to 7000 if I want 5000 - but that's not exactly "nice" :-)
Let's see - maybe another idea will come up :-)
Best regards,
Thomas
Eddi E. aus G. Wrote:
-------------------------------------------------------
> Moin,
>
> hab kein', aber wo liegt der (Denk-)Fehler?
>
> Im Preset sind 14.400 drin, und eben
> 3.780-4.500-5.220, sollte meinem Verständnis nach
> doch funktionieren, nicht gekappt?
>
Ja genau - so ist es im Preset auf der VBC - leider in der Realität dreht das Ding spürbar weniger - durch alle Bänke..
Man sieht es auch an den extrem niedrigen PWM Öffnungen 49% und so - dass er "mehr könnte" - speziell an 4s..
Heute mit 9600 probiert -> genau das gleiche Ergebnis - eingestellte Drehzahl und Log-Drehzahl (die real stimmt nach Bauchgefühl) passen nicht zusammen...
Ich könnte jetzt natürlich einfach 7000 einstellen, wenn ich 5000 will - aber das ist halt nicht "schön" :-)
Mal schauen - vielleicht findet sich ja noch eine Idee :-)
LG,
Thomas
Eddi E. aus G.
26 June 2026 10:3426.06.2026 10:34
Good morning,
Price questions...
What happens, what do you see, when you unplug the RPM cable (please also check the controller telemetry menu)?
Does the rotational speed change, and how – when you change the base gas?
If you switch the controller to position mode and/or enable pitch control in the setup, can you then fully control it?
Which firmware version is on the controller (this information isn't very helpful since I'm not familiar with it, but...), perhaps one thing was fixed in the last update (telemetry bug), and another was made worse? Would it work properly (or better) with a different/older version (if possible)?
So far you seem to be the only one experiencing this phenomenon, congratulations :-)
—Eddi
Born to fly ...
forced to work.
Moin,
Preisfragen ...
Was passiert, was siehst Du, wenn Du das RPM-Kabel absteckst (auch im Regler-Telemetrie-Menü bitte dann mal gucken)?
Verändert sich die Drehzahl, und wie-wenn Du das Basisgas veränderst?
Wenn man den Regler mal in den Stellermodus umstellt, dann und/oder gleich Pitchkontrolle im Setup, kann man ihn dann voll durchsteuern?
Welche Firmware ist auf dem Regler (bringt mir wenig die Info weil ich mich nicht auskenne, aber ...), vielleicht ist ja beim letzen Update eine Sache korrigiert worden (Telemetrie-Bug), und eine andere verschlimmbessert? Geht's mit 'ner anderen/älteren (falls möglich) wieder richtig(er)?
Bis jetzt bist Du scheinbar der einzige mit dem Phänomen, Glückwunsch :-)
—Eddi
Born to fly ...
forced to work.
RV
26 June 2026 17:1626.06.2026 17:16
I'll contact XL support... there he is already!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/26/2026 10:26PM by RV.
Ich funk mal den Support von XL an ... da isser schon!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/26/2026 10:26PM by RV.
Carl-Henning Siebert
26 June 2026 20:1726.06.2026 20:17
Hello Thomas,
Which Hobbywing software do you have installed on the controller?
greeting
Carl
Hallo Thomas,
Welche Hobbywing Software hast du auf dem Regler?
Gruß
Carl
thomas1130
26 June 2026 20:2026.06.2026 20:20
Hello Carl,
The new PL-04.1.07 has recently been released.
But I don't think that has anything to do with it - I had the same "problem" with the factory-delivered version...
But at least the rear end is noticeably better now - I'm quite happy with that... now I just need some serious revs 8-)
LG
Thomas
Hallo Carl,
seit kurzem die neue PL-04.1.07
Glaub aber das hat nichts damit zu tun - das "Problem" hatte ich auch schon mit der Auslieferungsversion...
Aber immerhin ist das Heck jetzt wirklich spürbar besser - damit bin ich schon recht zufrieden.. - jetzt brauch ich nur noch richtig Drehzahl 8-)
LG
Thomas
thomas1130
28 June 2026 07:5928.06.2026 07:59
Tried it again today with a specific goal in mind - and got some very "strange" results:
It does n't matter what headspeed I set - it always spins at the same RPM for each bank!?
Bank1 - approx. 3300 - Bank2 approx. 3700 - Bank3 approx. 4400
First I tried it with the values from the screenshot - result above..
Then, for the test, bank 3 was set to 7500 - but it still spins at 4400!??
That's really strange - as if the RPM were stored in the controller, and I was only specifying the banks from the transmitter??
Would that be possible?
LG
Thomas
Edited 1 time(s). Last edit at 06/28/2026 08:00AM by thomas1130.
Heute nochmals gezielt probiert - und ganz "merkwürdige" Ergebnisse:
Es ist völlig egal welchen Headspeed ich vorgebe - er dreht pro Bank immer in der gleichen Drehzahl!?
Bank1 - ca 3300 - Bank2 ca 3700 - Bank3 ca 4400
Zuerst mit den Werten aus Screenshot probiert - Ergebnis oben..
Dann zum Test Bank 3 auf 7500 gestellt - er dreht trotzdem mit 4400 !??
Ganz merkwürdig - wie wenn die Drehzahl im Regler hinterlegt wäre, und ich nur die Bänke von der Funke vorgebe??
Wäre das möglich??
LG
Thomas
Edited 1 time(s). Last edit at 06/28/2026 08:00AM by thomas1130.
RV
28 June 2026 09:5428.06.2026 09:54
Have you already checked if the RPM signal is arriving at the RPM pin of the stabilizer?
Try unplugging the TELEphone, letting it run, and checking if the RPM is displayed - and if it's correct.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/28/2026 09:54AM by RV.
Hast Du schon geprüft ob das RPM Signal am RPM Pin der Stabi ankommt?
Dazu mal TELE abziehen, laufen lassen und schauen ob RPM angezeigt wird - und auch korrekt ist.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/28/2026 09:54AM by RV.
thomas1130
28 June 2026 11:1028.06.2026 11:10
That was exactly it - Rainer, you're a genius - THX :-)
The mini-pin connector for the rpm signal was loose – and I didn't notice it because "RPMs were being displayed anyway" – but these were obviously only coming from the telemetry... :-)
rpm plug properly attached - and now the little guy is turning as he should :-)
Then I increased the BEC voltage from the preset 6.0V even further – to a cautious 7.4V – this was recommended to me elsewhere as an "improvement".
Thanks to everyone here.. :-)
Greetings from super-hot Vienna,
Thomas
PS: Additional question: What is the difference between 9600 and 14400 maximum RPM?
Does the stabilization system calculate more precisely internally – i.e., with higher digital resolution or something like that?
Edited 1 time(s). Last edit at 06/28/2026 12:28PM by thomas1130.
Genau das war es - Rainer du bist ein Genie - THX :-)
Der Mini-Pin-Stecker beim rpm Signal hatte einen Wackler - und ich hab es nicht bemerkt, da ja "eh Drehzahlen angezeigt" wurden - die aber offensichtlich nur von der Telemetrie kamen.. :-)
rpm-Stecker gescheit befestigt - und schon dreht der Zwerg wie er soll :-)
Dann hab ich die BEC Spannung von 6,0V aus dem Preset auch noch höher gesetzt - mal auf vorsichtige 7,4V - wurde mir anderenorts empfohlen als "Verbesserung"..
THX an Alle hier .. :-)
Grüße aus dem superheißen Wien,
Thomas
PS: Zusatzfrage: Was macht der Unterschied zwischen 9600 und 14400 max Drehzahl?
Rechnet da das Stabi intern genauer - also mehr digitaler Auflösung oder so?
Edited 1 time(s). Last edit at 06/28/2026 12:28PM by thomas1130.
ulrich
29 June 2026 23:4029.06.2026 23:40
This is an internal prescaler. With the lower setting, it's slightly more accurate. However, this shouldn't make any real difference, apart from the larger maximum value.
So long... Uli
http://www.vstabi.de
Das ist ein interner Vorteiler. Mit der geringeren Einstellung ist es ein klein wenig genauer. Das sollte aber keinen effektiven Unterschied ergeben, ausser der grössere Maximalwert.
so long ... Uli
http://www.vstabi.de