← XL Power Support

Speed controller at full throttle! RPM cable? translated

OEM models › XL Power Support · Started by Daniel M. on 29 July 2026 17:4229.07.2026 17:42
Daniel M. 29 July 2026 17:4229.07.2026 17:42
Hi everyone... I have a problem, as you can see in the picture! At that moment, the helicopter is flying terribly! Could this be due to the RPM cable (loose connection)? I also occasionally get clean logs... except for the severe vibrations. The elevator also revs up and everything behaves strangely! I'm worried the ESC is broken! Regards, Daniel

machine-translated from German · Show original
ulrich 29 July 2026 21:3929.07.2026 21:39
I'm guessing you have too much rear gain or torque extension. Could that be it?

It sounds rather strange at first, but the problem is that if the gain gets too high, the tail controller oscillates quite strongly, and the torque extension also places excessive demands on the main motor.

The rear end then becomes very "soft" and sometimes even starts to drift noticeably.

So long... Uli
http://www.vstabi.de
machine-translated from German · Show original
Daniel M. 30 July 2026 06:1530.07.2026 06:15
Good morning...yes, I know that feeling...what's puzzling me is that it doesn't happen all the time. Sometimes it flies well, and sometimes it doesn't...so I was thinking it might be a loose connection in the wiring! I'd like to know...if the RPM or telephoto cable has a loose connection...could that cause this? It also happened during the pre-setup! Regards, Daniel
machine-translated from German · Show original
Daniel M. 30 July 2026 08:2730.07.2026 08:27
Oh, I see... on my last flight, for example, I didn't have a single entry! And I flew roughly the same route! Regards, Daniel
machine-translated from German · Show original
Eddi E. aus G. 30 July 2026 09:1530.07.2026 09:15
Good morning,

Does this happen more frequently if you fly with several batteries in quick succession?
What else could be different between "if" and "if not like last time"?

What the VBar is reporting here is simply that it has to supply 100% power at certain times (and would like to supply more, but it can't), or it completely cuts it off (it would like to supply more, but it is limited).
If the RPM cable were faulty, it would display 'RPM sensor no signal', which can be ruled out based on the screenshot.

If the helicopter then 'becomes soft', that's a sign that a limit is really being exceeded somewhere.

What firmware is on the controller, which preset was loaded for it, or what was changed between before and after?

Grüßle

Eddi

Born to fly ...
forced to work.



Edited 1 time(s). Last edit at 07/30/2026 09:15AM by Eddi E. aus G..
machine-translated from German · Show original
Daniel M. 30 July 2026 09:5030.07.2026 09:50
Hi, the latest firmware from XL Power... so the telemetry bug disappears. The pre-setup from Mikado is specifically for the Stratos (it does it there too), and I got one from Carl (it happens there as well! But it flies better!). By the way, I fly with 4S; the Mikado pre-setup doesn't work for me with 3S! I had to significantly reduce the torque compensation (I can't remember the name right now)... and then it was too sluggish! But I'm no expert when it comes to settings! A colleague helped me... and he said the pre-setup is for 4S.
machine-translated from German · Show original
Daniel M. 30 July 2026 09:5430.07.2026 09:54
Oh yes, and my rear-end optimizer isn't set to 30...20...is that correct? I haven't changed anything!
machine-translated from German · Show original
Eddi E. aus G. 30 July 2026 10:2030.07.2026 10:20
Good morning,

I have to refer you to Carl, he's in charge there, and the setups are his too.
Basically, we only provide the platform so that you can directly load/set up the Stratos 200 without having to download or copy anything else.

Tail optimizer, 'normally' you learn it by flying, switching it on, using piros with defined stops on the right and left, after a few repetitions they feel correct(er), then you can possibly try manually increasing them, or slightly weakening the stronger side to have both sides equal (or you can leave it as is).

But with microcars, and especially with rear-mounted engines, so many control factors come into play that the automatic system may not lead to the best result, or rather, it depends on everything else.

Then, of course, you can manually optimize the stop on one side, then the one on the other, and then possibly balance it out.
Higher stop gain = harder (up to the performance limit...).

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Daniel M. 30 July 2026 10:2430.07.2026 10:24
Thanks in advance... I just wanted to make sure that the RPM cable or the telephone cable wasn't the problem.
machine-translated from German · Show original
Eddi E. aus G. 30 July 2026 12:1630.07.2026 12:16
Hi,

Nope.

RPM cable, log entry and fallback to the throttle curve.
Telemetry cable, end screen as if the helicopter was switched off, or log entries, controller disconnected, controller connected.

Don't be afraid to try it out, just unplug it, nothing will break ^^

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
MGU 30 July 2026 15:2130.07.2026 15:21
Daniel M. wrote:
-------------------------------------------------------
Hi, the latest firmware from XL power...so that the
> Telemetry bug disappears. The pre-setup of
> Mikado especially for the Stratos (that's where he does it)
> also) and I got one from Carl (since
It happens too! But it flies better now!
> By the way, I fly with 4s, the Mikado flies with 3s.
> Pre-setup didn't work for me! I had to be very clear about that.
> this torque compensation (I can't think of it now)
> the name) take it down....and then he was too
> Vague! But I'm no expert either.
> Things like settings! A colleague helped me.
> ...and he said the pre-setup was for 4s.


Could you provide the setup? I'd like to see what's different from the standard setup that you can choose from in the vbar.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless