← VBar NEO for external transmitters

The rear end moves somewhat jerkily/not consistently when controlled. translated

VBar › VBar NEO for external transmitters · Started by sonicgm on 10 October 2022 13:3010.10.2022 13:30
sonicgm 10 October 2022 13:3010.10.2022 13:30
Hello everyone,

I have the following problem with my new and standard Bell 430 (1:5 scale, Vario kit and mechanics, Kontronik motor and controller):

If I want to fly a tail turn very slowly, the tail turn is not consistently smooth, but somewhat jerky.
I have already tried all possible solutions I know of:
The tail rotor blade bearings were replaced as a precaution, even though they were only a few months old. Everything moves smoothly, even under load. No improvement.
- The tail control mechanism was completely redesigned compared to the standard version (thicker carbon fiber tube, play-free and absolutely smooth operation, even under load). No improvement.
- The tail servo has been replaced a total of three times (first Hitec, then MKS, now KST). None of the changes brought any improvement.
- Switched from Axxon to VBar Neo. No improvement.
- Tried various Neo settings (tail rotation rates, etc.). No improvement.
- Drive unit (tail rotor, tail shaft, stainless steel, standard) disassembled several times and checked for slippage or other damage. No improvement.

Finally, I ran the Bell without rotor blades while stationary and operated the tail rotor manually (i.e., via the linkage near the servo). Everything works smoothly with very little effort and without any problems.

I've exhausted all my solutions. This has been going on for about a year now. I could replace the tail rotor, but then more customers would have to be experiencing the same problem. Therefore, I don't think that would help.

Logically, the only explanation I can come up with for this behavior is that the control loop is essentially oscillating. That is, the signal comes from the transmitter, nothing happens at the tail, Neo compensates further, but now too much, compensates again, now too little, and so on. The cause is either the mechanics or the settings. However, I have checked, modified, or changed both.

Perhaps one of you might have some advice. Thanks for any help.
machine-translated from German · Show original
Eddi E. aus G. 10 October 2022 13:5510.10.2022 13:55
Hello,

I'm afraid (hopeful ;-) ), the answer is quite simple... and the self-given explanation is pretty much correct.

In the tail rotor Expert (requires Pro), please reduce the acceleration from the standard 55 to 35-25.

Grüßle

Eddi

Born to fly ...
forced to work.



2 mal bearbeitet. Zuletzt am 10.10.2022 13:56 von Eddi E. aus G..
machine-translated from German · Show original
sonicgm 10 October 2022 14:0210.10.2022 14:02
Hi Eddi,

Thanks for the quick reply. I have the Pro version. I'll check the acceleration this week and give you some feedback.
See you then
Best regards
Günter
machine-translated from German · Show original
sonicgm 11 October 2022 10:3611.10.2022 10:36
Hi Eddi,

The acceleration was set to 33, I'll try 25, maybe even just 20, and see how the rear end behaves.
Can I lower it to 10? Will that have any other effects?

Best regards
Günter
machine-translated from German · Show original
Eddi E. aus G. 11 October 2022 10:4411.10.2022 10:44
Hello Günter,

I actually don't know at what point it might have a negative effect; I haven't tested that yet.

But you could do it for each bank to be able to compare differences.

Another thing you could try is lowering I relative to P, normally 80 P 60 I, try lowering I to 50 or 40.
Perhaps turning a few points D will also help.

What kind of tail fins are on it? If it's a load-bearing airfoil/S-shaped, try symmetrical ones. And if in doubt, longer ones.

We initially tried VARIO pads, with limited success. Then we switched to NHP, which was better. Then Rainer built something , and with that it was (and still is after 12 years) practically perfect.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
RV 11 October 2022 12:3511.10.2022 12:35
Below 25, the rear end becomes very slack. I always like to use 28-30 as an estimate.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
sonicgm 11 July 2023 16:2011.07.2023 16:20
Hello,
Unfortunately, I only just got back to flying, hence the delayed feedback:

Nothing has changed with the recommended settings, and I'm starting to get desperate. The tail still moves slightly jerkily. I'm going to replace the tail blades, but apart from Blattschmied (S-shaped, which I ordered anyway) and Vario (which I've used on my Bell), I can't find any other manufacturer that offers 180 mm tail blades.
Do you know of any other manufacturers that offer larger (here: 180 mm) tail blades?

Best regards
Günter
machine-translated from German · Show original
RV 11 July 2023 19:3111.07.2023 19:31
I have the original variators on my UH 1D. They work perfectly. They are 156mm, though.

https://www.vstabi.info/forum/read.php?10,172594

https://www.vario-helicopter.biz/de/Heck/Heckrotorblaetter/Heckrotorblaetter-156-mm-grau::36804.html


Please provide some data (weight, number and size of main blades, head speed, tail drive ratio)...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 11.07.2023 19:31 von RV.
machine-translated from German · Show original
sonicgm 12 July 2023 08:1712.07.2023 08:17
Hello Rainer,

The Bell 430 weighs 16.3 kg and is equipped with a 4-blade rotor head (Vario) (2300 mm rotor diameter).
Vario rotor blades with S-shape, 1015 mm.

Head speed measured at 920 rpm.

I calculated a tail rotor gear ratio of 1:4.5 based on the number of teeth (ring gear 63 teeth and bevel gear to the tail rotor 14 teeth), which should result in a tail rotor speed of 4140 rpm. The tail rotor blades are 180 mm long and symmetrical, with a tail rotor diameter of 440 mm.

Your 156 mm Vario tail blades for the UH are also recommended for the Bell 230, at least in the same scale as my Bell 430. The only difference is the 4-blade rotor head on the 430 (instead of 2-blade on the 230)...

Thank you and best regards
Günter
machine-translated from German · Show original
RV 12 July 2023 22:4712.07.2023 22:47
1:4.5 oh wow... that's not much...

My PHT3-3 has a gear ratio of 1:4.67, and I also have the Vario spiral gear set at 1.0635 on the tail gearbox. That makes a total of 4.96. Plus, I only have the basic torque of two blades (of the same length) instead of four. Takeoff weight is 21.8 kg.

Normally, 4-blade thelis in the same weight class operate with smaller rotor circles than their 2-blade counterparts. Therefore, we have high drag here, primarily due to the four large blades – despite a lighter weight than mine. However, the centrifugal forces of the tail blades might also be a factor – it's possible that these large blades exert a strong pull, causing the thrust bearing to seize.

Quote: Finally, I ran the Bell without rotor blades while stationary and operated the tail rotor manually (i.e., via the linkage near the servo). Everything works smoothly with very little effort and without any problems.

If you feel confident enough (have someone hold the tail!!!) - try it with the blades. Don't worry, they'll center themselves first. Then operate them - but be careful - and always keep one hand on the motor OFF! - If it's difficult to turn, try using propeller torque weights (PMGs), check the thrust bearing, or try different large tail blades.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
sonicgm 13 July 2023 07:1513.07.2023 07:15
Hello Rainer,

I had mounted the tail blades while the aircraft was stationary during operation. I hadn't mounted the rotor blades on the rotor head during the test. There was a misunderstanding, or I worded it incorrectly.
I'll give it a try with the 156 mm tail blades anyway. It's not meant for 3D flying... and the effect should (hopefully) still be sufficient. I don't have any other options.

Best regards
Günter
machine-translated from German · Show original
RV 13 July 2023 07:4813.07.2023 07:48
Well, with the 156s I would definitely want to increase the tail rotor speed. You have four main blades with huge base torque – and then the overall effect of the tail rotor might be somewhat weak.

But – take it one step at a time. First the shorter blades, and if the rear end still doesn't provide enough power – increase the rear gearbox output a bit more.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
sonicgm 22 July 2023 10:3422.07.2023 10:34
Brief feedback:
I tried out the 156mm Vario tail blades (instead of the 180mm ones). And lo and behold: the tail now moves noticeably more consistently under control and isn't as jerky as before. I'm happy with the result and I think it's now the optimal setup. Perhaps a little fine-tuning of the settings is needed, but then it should be perfect.

What I had forgotten and only remembered because of your post: I had already installed the spiral-toothed pinions in the rear gearbox (Vario tuning accessories), which actually increased the rear wheel speed due to the changed gear ratio.

Apparently, in my case, the large rear blades, in conjunction with the increased engine speed at the rear, pushed the system to its limits in general (regardless of the Vstabi, as the same effect occurred with the BD Axon).

Interestingly, there is a note on the homepage regarding the spiral-toothed gearbox (which I believe was not listed two years ago) stating that the tuning gearbox should not be used with larger helicopters (> 2m rotor diameter).

Best regards
Günter



Edited once. Last edited on 22.07.2023 at 10:34 by sonicgm.
machine-translated from German · Show original
RV 22 July 2023 22:1722.07.2023 22:17
Okay - don't tell my Huey about the gearbox - she's been flying around with it for 4.5 years...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless