nzlsubzero
14 May 2024 11:1514.05.2024 11:15
Hi All
I'm struggling to get this setup working.
I want to be able to use the throttle for the speed.
I did check the videos from Rainer, but couldn't get it working.
normal - 0, 25, 50, 50, 50
Idle 1 - 60, 60, 60, 60, 60
idle 2 - 80, 80, 80, 80, 80
is there an easy way to do this?
Alternatively, how can I set fixed headspeeds for Idle 1 and 2?
Any tips will be greatly appreciated.
Thanks
Eddi E. aus G.
14 May 2024 11:4814.05.2024 11:48
Hi,
did you see this?
https://www.vstabi.info/en/node/1961#15
If you want a manual spool up (not very common any more these days ...), it'd be the alternative, route throttle through AUX3.
Kind regards
Eddi
Born to fly ...
forced to work.
nzlsubzero
14 May 2024 11:5914.05.2024 11:59
Hi Eddi
Thanks.
I currently have the Thr channel going to the ESC.
How can I set a specific value for Idle 1 and 2?
I’ll also look at the Aux3 option.
Eddi E. aus G.
14 May 2024 13:0014.05.2024 13:00
Hi,
please read, try, understand.
Our throttle logic is designed to have a three-position throttle switch (Off-Idle-Run), and a three-position bank switch (flight mode switch).
In the respective banks, you can enter three different throttle values (like 60-75-90 %).
Off is off.
Idle outputs the AR throttle value, autorotation throttle, keeps the motor spinning at low rpm, but allows for a quick emergency abort.
On outputs the throttle value per bank.
Your original throttle channel is not used. There is no direct link any more, and why, in the era of governors.
Even more so, if you can make any adjustment from your transmitter, at any time, if ... it's a VBar Control ;-)
Or, plan B, assign your original throttle channel to AUX3, and the VBar only routes through what you set up in your transmitter.
This is to provide for the olde ways :-) which are not bad ... just a bit outdated, in 2024 :-)
Kind regards
Eddi
Born to fly ...
forced to work.
nzlsubzero
15 May 2024 09:1615.05.2024 09:16
Hi Eddi
I'm not very familiar with Futaba TX. V Control would be my choice :-) Trying to help someone get their heli going.
How would the bank values be set to 60 - 75 - 90?
Using the AUX3 option, do you mean physically have the throttle connection into
aux3?
Thanks
Allen
Eddi E. aus G.
15 May 2024 10:1215.05.2024 10:12
Hi Allen,
are you setting up using the computer software?
There's a box for Throttle/Governor, where you enter a value.
Similar to VBar Control.
If you were helping from remote, I'd recommend you install/start up the setup software on your computer, so you see.
Doesn't required to have a VBar connected.
Use the bank switch to switch between banks with a live VBar connected, adjust values per bank, then.
AUX3, right, connect the throttle thingy (ESC, servo) to AUX3. Then, it's as if it was connected to a receiver.
Speaking of, if a full receiver is used, you could also connect to the receiver. Just mind Fail Safe: in case you were bypassing the VBar throttle logic, you must make sure that the motor/engine is shut down a) when disconnecting the receiver from the VBar and b) when switching off the transmitter (yes, you can do that with other transmitters, during operation ^^).
Cheers
Eddi
Born to fly ...
forced to work.
nzlsubzero
15 May 2024 10:5915.05.2024 10:59
Hi Eddi
Excellent, I managed to get the changes using the software and set desired values for flight modes. :-)
Really appreciate the help.
Thanks
Regards
Al
5 mal bearbeitet. Zuletzt am 15.05.2024 11:02 von nzlsubzero.
Eddi E. aus G.
15 May 2024 12:4715.05.2024 12:47
:-)
Born to fly ...
forced to work.