← VBar NEO for external transmitters

VBar Neo + Spectrum Satellite + suspension on AUX 3 - AUX3 doesn't work translated

VBar › VBar NEO for external transmitters · Started by markus710 on 1 March 2025 17:5701.03.2025 17:57
markus710 1 March 2025 17:5701.03.2025 17:57
I have the following setup:
VBar Neo + Spectrum Satellite + landing gear on AUX 3 (or 2, same result)
The helicopter is set up and all functions are working correctly (bank switching; motor; rescue).

Now I just want to connect a servo for the landing gear to AUX2 or AUX3. But I can't get it to work. It seems like nothing is getting through. Nothing is happening in the software, and the connected servo isn't responding.
I assigned the channels according to the software (8 and 9) and connected them to switches. The servo monitor on the remote control also displays the correct functionality.

But Neo doesn't care about that.

Where is my mistake? Basically, I just want to pass the channel through.



Edited once. Last edited on 02/03/2025 at 16:39 by markus710.
machine-translated from German · Show original
Eddi E. aus G. 3 March 2025 09:4103.03.2025 09:41
Good morning,

Servo monitor, OK, but what does the VBar software display?
If a 'live' :-) channel is assigned, the bar should also move.
If he doesn't, nothing will come through on the channel...
If in doubt, you can simply enter the channel numbers one after the other and see, for example, if I assign the roll channel to an AUX input, it will react to roll from the transmitter.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
markus710 3 March 2025 09:5303.03.2025 09:53
The VBar software shows absolutely nothing, no reaction whatsoever. I've configured channels 8 and 9 there and assigned them accordingly in the transmitter.
If I change the channels in VBar, for example, from AUX 2 and AUX 3 to 7, then the servos on outputs AUX 2 and 3 work, and the software also shows activity. However, since channel 7 is also used for bank switching, this isn't an option. (I just wanted to know if it works in principle.)

However, as soon as I assign channels 8 and 9 again, everything goes dead in vStabi. It seems as if vStabi is ignoring these channels, or rather, that they aren't being received.
machine-translated from German · Show original
Eddi E. aus G. 3 March 2025 11:0103.03.2025 11:01
Hmm... unfortunately, I can't contribute much more to that.

VBar retrieves the channel information transmitted by the satellite; it can do nothing more.
To the best of my knowledge, at least 8 channels, possibly even 12 (I'm not sure right now).

It _could_ be that depending on the setting in the transmitter (DSMX 11 ms or 22 ms, which transmitter/receiver offer/can offer during binding) different transmission speeds occur, because the amount of data must also fit sensibly/safely into the data packets.

So, would that possibly be another option, if we changed the 11 ms time to 22 ms time?

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
markus710 10 March 2025 11:4610.03.2025 11:46
Hi Eddi,
Thank you so much for trying to help me. Adjusting the binding settings didn't solve the problem either. So I've now accepted that it's simply not possible. Therefore, I've sold the FBL unit and replaced it with another one that can control all the channels of my Spektrum transmitter.

Thanks again
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless