Hello everyone!
I have a used helicopter with a VBar EVO with a V8 Pro Rescue.
The previous owner operated the helicopter directly with a VBar Control and also configured the VBar directly through it.
I now want to operate the helicopter with 2 Spektrum SPM9746 satellites connected to the two teleports.
I have already operated several helicopters with various VBars (Mini VBar, VBar Silverline, VBar NEO) each with 2 Spektrum satellites and have never had any problems with them.
This is my first VBar Evo.
Now to my actual problem:
I bound the two satellites to the remote control using a normal Spektrum receiver, as binding via the PC software didn't work for me (I found a solution for that here in the forum) - so far so good.
1 Tele Port (left port) works perfectly - each of the two (previously bound) satellites works on this port.
The first teleport (right port, marked in yellow in the image) unfortunately does not work as expected – the satellite always starts flashing rapidly (bind mode active) and can be found and bound. However, the second, previously working, satellite is then deactivated.
Every time the power supply is switched off and on again, the binding sequence starts from the beginning -> so unfortunately it doesn't work.
The previous owner had established a connection to the controller (YGE 205HVT) Tele-Port at exactly this Tele Port and displayed the controller's telemetry data accordingly on his VBar Control.
I understand that this won't work with my spectrum solution, and that's OK with me.
My plan was to change the transmitter-receiver configuration on the VBar in the PC software and to adopt the remaining settings from the previous owner, as the helicopter worked perfectly with them.
I have already tried the following things - unfortunately none of them solved my problem:
- New configuration via PC software
- Downloaded various apps (including V7) from the App Store and then updated them back to V8.
...unfortunately without success.
Is there any way to restore the VBar to its "factory settings"?
Does anyone have any ideas on how I can get the port on rails?
Thank you in advance for your help,
Wed
I have a used helicopter with a VBar EVO with a V8 Pro Rescue.
The previous owner operated the helicopter directly with a VBar Control and also configured the VBar directly through it.
I now want to operate the helicopter with 2 Spektrum SPM9746 satellites connected to the two teleports.
I have already operated several helicopters with various VBars (Mini VBar, VBar Silverline, VBar NEO) each with 2 Spektrum satellites and have never had any problems with them.
This is my first VBar Evo.
Now to my actual problem:
I bound the two satellites to the remote control using a normal Spektrum receiver, as binding via the PC software didn't work for me (I found a solution for that here in the forum) - so far so good.
1 Tele Port (left port) works perfectly - each of the two (previously bound) satellites works on this port.
The first teleport (right port, marked in yellow in the image) unfortunately does not work as expected – the satellite always starts flashing rapidly (bind mode active) and can be found and bound. However, the second, previously working, satellite is then deactivated.
Every time the power supply is switched off and on again, the binding sequence starts from the beginning -> so unfortunately it doesn't work.
The previous owner had established a connection to the controller (YGE 205HVT) Tele-Port at exactly this Tele Port and displayed the controller's telemetry data accordingly on his VBar Control.
I understand that this won't work with my spectrum solution, and that's OK with me.
My plan was to change the transmitter-receiver configuration on the VBar in the PC software and to adopt the remaining settings from the previous owner, as the helicopter worked perfectly with them.
I have already tried the following things - unfortunately none of them solved my problem:
- New configuration via PC software
- Downloaded various apps (including V7) from the App Store and then updated them back to V8.
...unfortunately without success.
Is there any way to restore the VBar to its "factory settings"?
Does anyone have any ideas on how I can get the port on rails?
Thank you in advance for your help,
Wed
Hallo zusammen!
Ich habe einen gebrauchten Heli mit einer VBar EVO mit V8 Pro Rescue.
Der Vorbesitzer hat den Heli direkt mit einer VBar Control betrieben und auch die VBar direkt darüber konfiguriert.
Ich möchte den Heli jetzt aber mit 2 Spektrum SPM9746 Satelliten an den beiden Tele-Ports betreiben.
Ich habe schon mehrere Helis mit diversen VBars (Mini VStabi, VStabi Silverline, VBar NEO) mit je 2 Spektrum Satelliten in Betrieb und hatte noch nie Probleme damit.
Das ist jetzt meine erste VBar Evo.
Nun zu meinem eigentlichen Problem:
Ich habe die beiden Satelliten mittels normalem Spektrum Empfänger mit der Fernsteuerung gebunden, da das Binden über die PC-Software bei mir irgendwie nicht funktioniert (Lösung dafür hab ich hier im Forum gefunden) - so weit alles gut.
1 Tele Port (linker Port) funktioniert einwandfrei - jeder der beiden (vorher gebundenen) Satelliten funktioniert auf diesem Port.
1 Tele Port (rechter Port, im Bild gelb markiert) funktioniert leider nicht wie gewünscht - der Satellit beginnt immer schnell zu blinken (Bind-Modus aktiv) und kann auch gefunden & gebunden werden. Jedoch wird dann der 2te, vorher funktionierende, Satellit deaktiviert.
Jedes Mal Versorgungsspannung aus & wieder ein beginnt die Bindesequenz von vorne -> funktioniert also leider nicht.
Der Vorbesitzer hatte an genau diesem Tele Port eine Verbindung mit dem Regler (YGE 205HVT) Tele-Port hergestellt und die Telemetriedaten des Reglers entsprechend an seiner VBar Control angezeigt.
Dass das mit meiner Spektrum-Lösung nicht funktioniert ist mir klar und auch OK für mich.
Mein Plan war, ich ändere die Sender-Empfänger Konfiguration an der VBar in der PC-Software und übernehme die restlichen Einstellungen vom Vorbesitzer, da der Heli damit perfekt funktioniert hat.
Folgende Dinge habe ich schon versucht - leider hat nichts davon mein Problem gelöst:
- Neue Konfiguration per PC Software
- verschiedene Apps (auch V7 )aus dem App-Store geladen und dann wieder auf V8 upgedatet
...leider ohne Erfolg.
Kann man die VBar irgendwie wieder in den "Auslieferungszustand" versetzen?
Hat noch jemand eine Idee, wie ich den Port auf Schiene bekommen kann?
Vielen Dank schon mal für eure Hilfe,
Mi
Ich habe einen gebrauchten Heli mit einer VBar EVO mit V8 Pro Rescue.
Der Vorbesitzer hat den Heli direkt mit einer VBar Control betrieben und auch die VBar direkt darüber konfiguriert.
Ich möchte den Heli jetzt aber mit 2 Spektrum SPM9746 Satelliten an den beiden Tele-Ports betreiben.
Ich habe schon mehrere Helis mit diversen VBars (Mini VStabi, VStabi Silverline, VBar NEO) mit je 2 Spektrum Satelliten in Betrieb und hatte noch nie Probleme damit.
Das ist jetzt meine erste VBar Evo.
Nun zu meinem eigentlichen Problem:
Ich habe die beiden Satelliten mittels normalem Spektrum Empfänger mit der Fernsteuerung gebunden, da das Binden über die PC-Software bei mir irgendwie nicht funktioniert (Lösung dafür hab ich hier im Forum gefunden) - so weit alles gut.
1 Tele Port (linker Port) funktioniert einwandfrei - jeder der beiden (vorher gebundenen) Satelliten funktioniert auf diesem Port.
1 Tele Port (rechter Port, im Bild gelb markiert) funktioniert leider nicht wie gewünscht - der Satellit beginnt immer schnell zu blinken (Bind-Modus aktiv) und kann auch gefunden & gebunden werden. Jedoch wird dann der 2te, vorher funktionierende, Satellit deaktiviert.
Jedes Mal Versorgungsspannung aus & wieder ein beginnt die Bindesequenz von vorne -> funktioniert also leider nicht.
Der Vorbesitzer hatte an genau diesem Tele Port eine Verbindung mit dem Regler (YGE 205HVT) Tele-Port hergestellt und die Telemetriedaten des Reglers entsprechend an seiner VBar Control angezeigt.
Dass das mit meiner Spektrum-Lösung nicht funktioniert ist mir klar und auch OK für mich.
Mein Plan war, ich ändere die Sender-Empfänger Konfiguration an der VBar in der PC-Software und übernehme die restlichen Einstellungen vom Vorbesitzer, da der Heli damit perfekt funktioniert hat.
Folgende Dinge habe ich schon versucht - leider hat nichts davon mein Problem gelöst:
- Neue Konfiguration per PC Software
- verschiedene Apps (auch V7 )aus dem App-Store geladen und dann wieder auf V8 upgedatet
...leider ohne Erfolg.
Kann man die VBar irgendwie wieder in den "Auslieferungszustand" versetzen?
Hat noch jemand eine Idee, wie ich den Port auf Schiene bekommen kann?
Vielen Dank schon mal für eure Hilfe,
Mi
machine-translated from German · Show original