Holgi_01
16 May 2026 02:4116.05.2026 02:41
Hello, collective intelligence.
I finally want to use the Neo's speed control function for my Nitros.
I've only ever flown V-curves before. :-(
The website
https://www.vstabi.info/de/node/2032 refers to a 3-point throttle curve, which is also intended to serve as a "backup" in case the sensor etc. fails.
Since I use a Graupner MZ16, is this a V-curve that I set in the transmitter, or is it an "internal" V-curve that is stored in the NEO?
I always assumed that when using the regulator, a throttle curve is always stored.
Furthermore, something I didn't quite understand: Do I set the base throttle value roughly as I see it on my current throttle curve? For example, if the lower value of the throttle curve in the transmitter is 55 percent, do I take this value and enter it as the starting value in the PC software?
As always, I would be very grateful for a reply.
Best regards
Holger
Hallo Schwarmntelligenz.
Ich möchte nun eeeeendlich die Reglerfunktion des Neo für meine Nitros nutzen.
Bisher immer nur V-Kurve geflogen. :-(
Auf der Seite
https://www.vstabi.info/de/node/2032 wird hier von einer 3-Punkt Gaskurve gesprochen, die unter anderem auch als "backup" dienen soll, für den Fall, dass der Sensor etc. ausfällt.
Da ich eine Graupner MZ16 nutze, spricht man hier von einer V-Kurve die ich im Sender einstelle, oder handelt es sich um eine "interne" V-Kurve, die im NEO hinterlegt wird?
Ich ging immer davon aus, dass bei der Regler Nutzung, immer eine Gasgerade hinterlegt wird.
Des weiteren, was ich nicht ganz verstanden habe, den Wert des Basisgas, stelle ich in den Werten etwa so ein, wie ich an meiner bisherigen Gaskurve ablese? Also z.B. unterer Wert der Gaskurve im Sender ist 55Prozent und diesen Wert nehme ich und trage ihn als Ausgangswert über die PC-Software ein?
Wie immer, wäre ich ich über eine Antwort sehr dankbar.
Viele Grüße
Holger
RV
16 May 2026 09:1016.05.2026 09:10
Hello Holger,
The throttle curve is stored in the VBar and is determined by the base throttle (throttle value for target RPM at zero pitch on the ground, lowest point of the V-curve) and the addition for pitch.
Simply use a servo to check your Graupner settings and first adjust the base throttle, then the additional throttle accordingly.
In the transmitter itself, only the bank switching is relevant for the 3 speeds and curves in the stabilizer.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hallo Holger,
Die Gaskurve ist im VStabi hinterlegt und wird bestimmt durch das Basisgas (Gaswert für Ziel-RPM bei Nullpitch am Boden, niedrigster Punkt der V-Kurve) und der Zugabe für Pitch dann.
Schau Dir einfach mittels Servo Deine Stellungen bei Graupner an und dreh zuerst das Basisgas, dann die Zugabe entsprechend ein.
Im Sender selber ist dann nur die Bankumschaltung relevant für die 3 Drehzahlen und Kurven im Stabi.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Holgi_01
28 May 2026 01:0428.05.2026 01:04
So I can do whatever I want... somehow nothing happens.
I can adjust the base gas values however I want, but I don't get any change in the RPM.
The magnet is detected when the motor is turned, and when I have the helicopter connected to the laptop at idle, the software shows me approximately 500-530 RPM.
Current status: on bank 1, my Graupner graph shows a straight line of 52 percent, which should be approximately 75 percent according to the conversion table; on bank 2, my Graupner graph shows approximately 60 percent as a straight line; on bank 3... something...
I've also tested completely different values with similar results.
When I switch from Bank 1 to Bank 2 in flight, I notice the increase in RPM during my straight climb, but I don't notice any difference when changing the base throttle or pitch input. And when I'm doing moderate climbs, the engine eventually starts to stall, regardless of whether I set the pitch input to 20 or 100.
The motor seems to be set up quite well to me; I've always flown in a V-curve so far.
The log file contains entries such as "RPM controller on pitch" and "RPM controller at lower throttle limit".
and then messages from the speed controller being at its limit.
What could I have done wrong? I can't adjust the number of magnets with the PC software, and I have one magnet with the active side facing the sensor and the other with the passive side facing down. The conversion ratio is also correct.
And I'm using the XGuard sensor. :-/
I've attached one of the Lofiles. Unfortunately, I can't attach the file itself as a .txt file, so here's a screenshot. Maybe that will explain something.
Thank you and best regards
Holger
Also ich kann machen was ich will.... irgendwie tut sich da nix.
Ich kann die Werte vom Basisgas einstellen wie ich möchte, aber ich habe keine Veränderung der Drehzahl.
Magnet wird bei Drehen des Motors erkannt und wenn ich den Heli im Leerlauf am Laptop angeschlossen habe, zeigt mir die Software ca. 500-530 RPm an.
Aktueller Stand: auf Bank 1 habe ich in meiner Graupner eine Gerade von 52 Prozent, das müsste laut Umrechnungstabelle ca. 75 sein und auf Bank 2 habe ich in meiner Graupner ca. 60 Prozent als Gerade, auf Bank 3... irgenwas...
Ich hatte auch schon völlig andere Werte getestet mit ähnlichem Ergebnis.
Wenn ich im Flug von Bank1 auf Bank2 wechsel, merke ich zwar den Drehzahlanstieg meiner Geraden, aber ich merke keinen Unterschied bei der Umstellung von Basisgas oder Pitsch Zugabe. Und wenn ich moderate Steigflüge mache, fängt der Motor irgendwann an zu würgen. Egal ob ich Pitschzugabe von 20 oder 100 eingebe.
Motor ist für mein Empfinden ganz okay eingestellt, bin ja bisher immer V-Kurve geflogen.
Im logfile sind Einträge wie Drehzahlregler auf Pitch und Drehzahregler am unteren Gaslimit.
und dann Meldungen von Drehzalregler am Anschlag.
Was könnte ich denn da falsch gemacht haben? Magnetanzahl kann ich ja mit der PC Software nicht einstellen und ich habe einen Magneten mit aktiven Seite in Richtung Sensor und den Anderen mit der passiven Seite nach unten. Das Überzetzungsverhältniss stimmt auch.
Und als Sensor nehme ich den XGuard. :-/
Ich gebe mal eines der Lofiles im Anhang dazu. Das file selbst, kann ich leider nicht als .txt anhängen. daher mal als screenshot. Vielleicht erklärt das ja etwas.
Danke und allerbeste Grüße
Holger
RV
28 May 2026 16:2928.05.2026 16:29
Questions:
- Was the reset also activated when selecting the Nitro controller (a red box appears...)
- The statement: "I can't adjust the number of magnets with the PC software" is incorrect. Please refer to Sensor Configuration 2 in the controller setup ;-) - Simply hover your mouse over the number there... tooltips will always appear ;-)
- In setup mode, does it also run through the entire range from engine off (pitch stick throttle on) to full throttle?
Since no switches are visible in the log, how is the motor switch configured (receiver tab) and how is the motor off switch configured? How exactly does this work with the external transmitter? In which position is it started, what is the idle speed then, etc.?
Since this is a NEO, the RPM must be fixed for each bank in the stabilizer. The percentage of the "throttle line" is irrelevant here; you can use it to switch between banks 1-3 for 3 RPM changes depending on the line.
- How are the banks switched, what are the target RPMs?
All these things motivated us years ago to simply combine this unnecessarily complicated intermediate layer of "unknown transmitter and its programming" and the PC software into a VBar Control...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 28.05.2026 16:31 von RV.
Fragen:
- wurde auch bei der Nitro Regler Auswahl der Reset dann betätigt (Kommt so ein roter Kasten ...)
- Die Aussage: "Magnetanzahl kann ich ja mit der PC Software nicht einstellen" ist falsch. Bitte im Regler Setup 2 Sensor Konfig beachten ;-) - Einfach mal mikt der Maus über der Zahl dort hovern ... dann kommen immer Tooltips ;-)
- Wird im Setup Modus auch von Motor aus (Pitchknüppel Gas ein) bis Vollgas alles abgefahren?
- Da im Log keine Schalter zu erkennen sind - wie ist (Tab Empfänger) der Motor Schalter konfiguriert und wie ist der Motor Aus Schalter konfiguriert? Wie geht das dann genau mit dem Fremdsender? In welcher Stellung wird angelassen, wie ist der LL dann usw.
- da es sich um eine NEO handelt ist die RPM fest PRO BANK im Stabi zu hinterlegen. Die %-e der "Gasgerade" sind hier egal, man kann damit die Bänke 1-3 Schalten für 3 RPM je nach Gerade.
- wie werden die Bänke geschaltet, was sind die Ziel RPMs da?
Alles Dinge die uns mit dazu bewegt hatten bereits vor Jahren diese immer wieder unnötig komplizierte Zwischenschicht "Sender unbekannter Art und dessen Programmierung" sowie die PC Software einfach mal in einer VBar Control zu vereinen ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 28.05.2026 16:31 von RV.