← VBar NEO for external transmitters

packet loss with old NEO on new model translated

VBar › VBar NEO for external transmitters · Started by cudaboy_71 on 7 June 2026 20:0407.06.2026 20:04
cudaboy_71 7 June 2026 20:0407.06.2026 20:04
I previously had this v1 NEO with vcontrol satellite for many years on an xl550 electric model. i recently got a new EVO for that model, and put th old v1 NEO with satellite on a new XL nimbus nitro.

From the first flight I am struggling with lost packets and going in to failsafe. After 5 tries and the attempts at fixing below there is no change. Luckily, they are only momentary which brings the motor to idle and i have no control for only .5 second. So I land without incident.

Of note: because i'm running a satellite on the neo i'm using both Aux2 and Aux3 and ran out of connection ports for my backup guard pack; So, I'm running the backup guard in to Aux2 and using the top space of that connector for the signal pin of the satellite. Do you think there can be interference from the backup guard sharing the connector with the satellite pin?

Because I'm running a satellite, I tried using a spare I had on hand with no change in results. I also tried another satellite cable. This should eliminate the satellite or the attaching cable from consideration since I have tried different ones without resolving the issue.

Aside from that, I've tried to isolate the satellite cables from the rest of the connectors to mitigate interference. All 5 servos, main 2s 8.4v power, and the RPM signal wire are run down the port side of the model, and the satellite and backup guard are on the starboard side.

The model is designed to ground the belt by design, and i have verified continuity from the rear belt idler that touches the belt at the rear of the model, to the main frame. After the first issues, i even ran a single wire from the frame to a ground port of the vbar itself (I have done this on other models when I have issues, too. But, no resolution this time)

I could post logs, but they only show RC Input packets lost, immediately followed by RC Failsafe activated. Aside from that the usual 'Governor Full throttle' and occasional 'High Vibration Level' alerts that I get often with nitro models.

Any ideas to try next?
RV 7 June 2026 21:3207.06.2026 21:32
Hello,

about the backup - this is ok here, the power sockets are empty - so use it ;-)

Also about the backup - those backups are mader for emregency landings and can almost not help with voltage spikes from reversing servos. - But if this will be the case - you will be able to reproduce thsi with apitch pump test and no motor running. Please try, have a look in the log afterwards.

Could you attach images of all the hookup, especially antenna and the cable to the Sat?

Could you probably do a idle test run w/o blades to see if it is there in idle too? - if not there spool it up and watch the logs again?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
cudaboy_71 8 June 2026 15:5308.06.2026 15:53
Please tell me more about the voltage spikes from reversing servos. I've never had this issue, so I don't know about it. But, in fact yes after pitch pumping on the bench i was able to get a failsafe error. So, if this is the issue (or one issue) I need advice how to fix it. I am running Theta THM988 servos on cyclic and throttle; Older 4.8v Futaba BLS251 on tail. Maybe some settings in the Vcontrol EVO for these servos? Or some other kind of filter?

I do like the backup guard device for emergency landings as you identified. So, I would like to leave it on—but also something else to help with the spikes.

I have attached some photos; I will be able to do the run up test this evening, but not now.

Thank you! Dateianhänge:
öffnen | Download - nimbus_photos.zip (5.26 MB)
RV 8 June 2026 20:0008.06.2026 20:00
Okay - i'll bring some light in here:

The external Sat gets direct power from RC, so it is always hit by any disturbances here.
If it would be a NEO/EVO with internal sat - the disturbances might have been filtered by the NEO/EVO regulators.

This is the main difference - and might be a reason why not all see those issues.

Anyway - the reverse current is a thing which we detected and published in 2013 (!!!) here which gave us a small shitstorm form some servo brands but at the end the all took care for it - almost:

General:
https://www.vstabi.info/en/node/1422

Example:
https://www.vstabi.info/en/node/1484

Solution ... best would be use other servos on swashplate. The BLS251 is w/o any doubt okay. As a workaround you can add a standard capacitor with 16 or 25V 4700 uF directly to one of the sockets (probably Y-Harness) - this will dampen the regarding effects here. I bet this will solve it!

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
cudaboy_71 9 June 2026 02:5209.06.2026 02:52
I guess if I never had the problem before I didn't read about the issue in 2013 :-) I will install the cap and report back.

Thank you!!!
RV 9 June 2026 06:2009.06.2026 06:20
:-) :-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
cudaboy_71 11 June 2026 20:5311.06.2026 20:53
I had high hopes :-(

I put a 25V 4700uF cap in to a Y-harness. I bench tested by adding some hand pressure to the main blades and pitch pumping slowly and quickly for 30 seconds. I could not get it to lose packets/failsafe. So, I tried a flight this morning. But, it went to failsafe after only 50 seconds from spoolup.

I am out of ideas except for buying new servos (which will only be last resort—i just bought these new for this build); but, if that is really the cause then I guess that's the answer. any other ideas to try first? I have plenty of other antennas mounted to the boom. But, I can try moving it *shrug*
RV 11 June 2026 22:4711.06.2026 22:47
One more question:

Which power supply does this model have?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
cudaboy_71 12 June 2026 03:0112.06.2026 03:01
this is the nimbus nitro, so no BEC; I'm running an ovonic brand 2s 2200mah 50C flight pack as 'receiver pack' mounted on the front plate for best balance/CG. this pack has 12awg wire to a full size deans connector. I made a custom cable to the rear plate where the NEO is mounted. There is the deans connector to connect the flight pack soldered to 22cm of awg18 battery wire then soldered to a 22awg servo connector that plugs in to the NEO for power.

Additionally, there is the scorpion backup guard from mikadousa:
https://shop.mikadousa.com/Scorpion-Backup-Guard-II-Power-Board_p_2656.html
this is powered by ovonic 2s 50C 1000mah pack.

And, now the 25V 4700uF cap are the only sources of power to the NEO

The last bit of electronics other than that is the onboard glow system:
https://www.aliexpress.us/item/2251832668670925.html

I should note i have this exact same 2s lipo, backup guard and same lipo, and onboard glow system running on Glogo 690 for years with zero issue. But, the Glogo is running Neo vlink...not the sat antenna.

edit: i forgot about the JR VR5203 that is running on the new Nimbus nitro to step down the voltage for the BLS251.



3 mal bearbeitet. Zuletzt am 12.06.2026 03:05 von cudaboy_71.
RV 12 June 2026 17:4612.06.2026 17:46
Hmmm ... sounds all nice on first view.

As said - the VBar with integrated Vlink has a big advantage here.

But - as you have seen the issue on the bench with a pitch pump test - i would:

- do it in the original configuration again to prove it
- remove the glow electronic (unplug all), redo the test
- remove the backup guard (unplug), redo
- remove the tail servo regulator (unplug), redo
- remove 1 swash servo (try all 3), redo

I am curious if we might have a point where the issue stops and gets back if you reverse the regarding step.

Another question - the cable from Battery into the VBar - are ther 1 or 2 plugs to feed the VBar?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 12.06.2026 17:47 von RV.
cudaboy_71 12 June 2026 23:0412.06.2026 23:04
ok, so it sounds like I'm not doing anything dumb here LOL

I will do the tests you recommended, just because it will only take 5 minutes, and report my findings.

But, I think the easiest thing to do next is put the new EVO Vbar on this nitro.

As I stated initially, this NEO + Sat was on the 550 electric airframe originally for years with zero issues--even flying the same Theta THM988 on cyclic--the reason I got them again for the nitro.

I got a new EVO for the new Nimbus Nitro kit, but the EVO Vbar came many months before I could build the Nimbus so I just put it on the electric 550 because it was my first EVO and wanted to try the v8.2 software.

I think I'll put the EVO Vbar on the nitro and see if there are issues; if not I'll leave it and return the NEO + Sat to the electirc model where I know it works well.
cudaboy_71 13 June 2026 18:1913.06.2026 18:19
I have been unable to get the lost packets/failsafe on the bench now after 15 minutes of trying. I put it back as it was originally without the capacitor; tried loading the cyclic servos to stall. The only thing I did not try was starting the engine, as it was too late and my neighbors would not appreciate it.

So, I have just moved the new EVO to this airframe and added the capacitor for safety; and the NEO back to the electric. Fingers crossed for success now!
RV 14 June 2026 08:2114.06.2026 08:21
Okay - so please do some bench tests and careful flying to be sure everything goes well.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
cudaboy_71 14 June 2026 22:1514.06.2026 22:15
Did a range check at the field with the EVO on the new nitro kit, motor running (idle) with heavy pitch pump and cyclic—no events in the log. One easy 1-minute flight then land and check the logs.
Then two full, hard 3d flights. No issues with the new EVO.

3 hard 3D flights using the same NEO + sat on the electric heli it was taken off of. Zero issues or events in the logs.

The ONLY difference is this is a different field. There is an airplane event at the field i was having packet loss. So, I will be very careful going back to that field. Other than this no idea what the issue was.
VStabi VStabi Pioneer of Flybarless