Bernd S.
10 March 2026 06:3510.03.2026 06:35
Good morning,
I'm planning a redesign of my 2012 Logo 600SE.
Do the newer V2 side panels fit without any problems?
Because of some renovations, the old ones aren't as beautiful anymore.
And since I still have parts, it might be worth the effort to rebuild it.
Regards, Bernd
Moin,
ich plane Überarbeitung meines 2012er Logo 600SE.
Passen die neueren V2 Seitenteile problemarm ?
Wegen einigen Umbauten sind die Alten nicht mehr so schön.
Und da ich noch Teile habe könnte der Aufwand lohnen das mal neu aufzubauen.
Gruß Bernd
Eddi E. aus G.
10 March 2026 09:2010.03.2026 09:20
Hi Bernd,
Oh dear, that question was already old news ten years ago :-)
Seriously though: take a look at the
manual for the last 600 SE.
Besides the side panels, you need the battery plate and the quick-release fastener, and small parts, hood support (which can also be adapted if necessary), the chassis reinforcements are also new (old ... new ;-) ).
But definitely problem-free!
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Bernd,
oh je, die Frage war schon vor zehn Jahren kalter Kaffee :-)
Ernst beiseite: schau Dir mal die
Anleitung vom letzen 600 SE an.
Neben den Seitenteilen braucht's die Akku-Platte und den Schnellverschluss, und Kleinteile, Hauben-Abstützung (kann man ggfs. auch anpassen), die Chassis-Verstärkungen sind auch neu (alt ... neu ;-) ).
Aber problemarm auf jeden Fall!
Grüßle
Eddi
Born to fly ...
forced to work.
Bernd S.
10 March 2026 10:0210.03.2026 10:02
Yes, sir ;-)
Sure, but I've only flown occasionally in recent years and haven't been reading along here.
Therefore, I was living in a time capsule.
Thanks for the information!
Bernd
Jawohl Chef ;-)
Klar, ich habe die letzten Jahre aber ja auch nur ab und zu geflogen und hier nicht mitgelesen.
Von daher lebte ich in einer Zeitkapsel.
Danke für die Infos !
Bernd
Eddi E. aus G.
10 March 2026 11:4210.03.2026 11:42
:-) it's all ok :-)
If you had a T-Rex or another helicopter from 2012, it would be a different story ^^ you'd really have to sharpen your carving knife if you needed parts or wanted to upgrade :-)
—Eddi
Born to fly ...
forced to work.
:-) alles gut :-)
Hättste einen T-Rex oder anderen Heli von 2012, wäre es nochmal anders ^^ da müsste man schon mal das Schnitzmesser schärfen, wenn man noch Teile bräuchte oder upgraden wollte :-)
—Eddi
Born to fly ...
forced to work.
Bernd S.
21 March 2026 10:2521.03.2026 10:25
I'm not complaining either ;-) .
I also managed to make the "botched" one (due to telemetry overkill) look nice again.
New side panels will be installed when parts need replacing due to wear and tear; I still have belts, pressure rollers, etc. in stock - but everything is currently in excellent condition.
The quick-release fastener is nice too - I'll keep that in mind and thanks for the info.
But first, let's go flying!
Bernd
Ich meckere ja auch nicht ;-) .
Ich habe auch den "verbastelten" ( durch Telemetrieübetreibung ) wieder schick hinbekommen.
Neue Seitenteile kommen dann wenn Teile wegen Verschleiß neu müssen, Riemen und Andruckrollen usw. habe ich noch im Lager - aktuell aber da alles noch bestens.
Die Schnellverschluss(s)ache ist ja auch nett - habe das im Auge und danke für die Info.
Jetzt wird aber erst mal geflogen !
Bernd