lucasuk86
6 Juli 2023 21:1906.07.2023 21:19
So when I'm in idle 1 (headspeeed 1600) I have no issues. But as soon as I go into idle up 2 (1800 head speed) the helis receiver back drops loads. The end points on the nitro servo are fine. So I'm thinking is this to do with the Integral setting in the Vbar software? If so do I just reduce this setting? or is this something else entirely?
Any support would be much appreciated
Setup
Vbar neo
Futaba 14sg
Eddi E. aus G.
7 Juli 2023 10:4807.07.2023 10:48
Hi,
a voltage drop is usually not a thing of settings, unless a servo would bind and draw excessively high amps.
And even then, the blocking current is usually way less than the peak current in changes of direction, which happen all the time on the main rotor or the tail rotor.
It's a thing between the consumers and the power supply.
What servos and what power supply are you using, and how's everything wired?
Kind regards
Eddi
Born to fly ...
forced to work.
lucasuk86
7 Juli 2023 15:0407.07.2023 15:04
I can cruise around at 1600 head speed no problems. But as soon as I go above 1700+ the reciever battery drops voltage down to 7volts (2 cell lipo).
So I checked the throttle servo in vbar software to make sure endpoints were OK and they were.
Why else would I get this problem?
lucasuk86
7 Juli 2023 15:3607.07.2023 15:36
Eddi E. aus G. Wrote:
-------------------------------------------------------
> Hi,
>
> a voltage drop is usually not a thing of settings,
> unless a servo would bind and draw excessively
> high amps.
> And even then, the blocking current is usually way
> less than the peak current in changes of
> direction, which happen all the time on the main
> rotor or the tail rotor.
> It's a thing between the consumers and the power
> supply.
>
> What servos and what power supply are you using,
> and how's everything wired?
>
> Kind regards
>
> Eddi
Thanks for kindly helping much appreciated. I have set the max and min throttle servo throw in vbar so it shouldn't bind should it?
My set up is as follows
Vbar Neo Pro latest firmware
Futaba R7008SB reciever
Futaba 14sg transmitter
Futaba S3071 throttle servo
JR NXB89G tail
JR NX8935 cyclic
Os 105hzr
Optipower 2cell reciever lipo
Optipower ultraguard
Hirobo Freya
lucasuk86
7 Juli 2023 17:2607.07.2023 17:26
5000mah 2 cell lipo for reciever
RV
7 Juli 2023 20:4007.07.2023 20:40
Is there some kind of switch in between?
How strong are all electrical connections?
Is the battery connected to VBar or RX?
How old is the battery?
How is it monitored?
The Voltage drop is usually not a thing of the VBar - we just pass the voltage through.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
lucasuk86
8 Juli 2023 01:0308.07.2023 01:03
RV Wrote:
-------------------------------------------------------
> Is there some kind of switch in between?
> How strong are all electrical connections?
> Is the battery connected to VBar or RX?
> How old is the battery?
> How is it monitored?
>
> The Voltage drop is usually not a thing of the
> VBar - we just pass the voltage through.
Yes there is an off/on switch
Electrical connections are fine, no overheating or anything
Battery is connected to vbar not RX
Battery is about 3 years old but stable
Monitored via telemetry through futaba transmitter
RV
8 Juli 2023 10:4608.07.2023 10:46
I would like to have more details.
"I have a switch" is not as detailed as needed for troubleshooting.
Please describe exactly which battery, cables (lenght, size), which switchm how many sockets used etc. - simply the complete chain.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
lucasuk86
9 Juli 2023 15:4509.07.2023 15:45
Hello Rainer
Thank for your patience. I have found the culprit. 1 of the cells in the reciever lipo was poor. Changed the battery and now all ok
1 mal bearbeitet. Zuletzt am 09.07.2023 15:45 von lucasuk86.
RV
9 Juli 2023 22:1309.07.2023 22:13
:-) :-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.